Adjustments, Ploughing and Molding | Craftsman 113.29921 instruction

Basic Saw Operations (continued)

Ploughing and Molding

Ploughing fs grooving with the grain the tong way of the workpiece, using the fence Use featherboards and push sticks as required

Molding is shaping the workpiece with the grain the long way of the workpiece, using the fence. Use feather- boards and push sticks as required

Molding Cutting

Instructions for operating the molding head are contained in a booklet furnished with the molding head..

Always use the molding insert listed under recom-

mended accessories.

When using the molding head it will be necessary to remove the blade guard and spreader Use caution Use miter gauge, fence, featherboards, or push sticks, etc., as required

blade guard and spreader when you finished plough- I I WARNING: For your own safety, always replace the

ing or molding.

Adjustments

and remove plug from power source outlet before 1 WARNING: For your own safety, turn switch "OFF" making any adjustments,

Miter Gauge

NOTE: The graduations are manutactured to very close tolerances which provide ample accuracy for fine wood- working In some cases where extreme accuracy is required, when making angle cuts, for example, make a trial cut and then recheck it

The head should be square (90°) with the bar when the pointer points to "0"

To check for squareness, place an accurate square on the miter gauge it the head is not square with the bar:

1 Loosen the lock knob

2.Position the head square with the bar Tighten the lock knob

3Loosen the screw and adjust the pointer, so it points to zero

The swiveling movement of the head can be adjusted by tightening or loosening the set screw located inside of the head using a 1/8" hex "L" wrench

...................

Ploughing

Molding

Miter Gauc Knob Pointer

Head

Bar

36

Image 36

Craftsman 113.29921 owner manual Adjustments, Ploughing and Molding, Molding Cutting, Mended accessories

Contents

Two Table Extensions Rip Fence Miter GaugeSears, Roebuck and Co., Hoffman Estates, IL US,A Save This Manual For Future Reference Safety Instructions For Table Saw Safety Signal Words Before Using The SawWhen Installing Or Moving The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, IL Before Each Use Safety Instructions For Table Saws Dress for safetyPlan Ahead To Protect Your Eyes, Hands, Face and Ears Whenever Sawblade Is Spinning Additional Safety Instructions While Thru-sawingGrain Featherboard Glossary of Terms for Woodworking Miter CutMolding Motor Specifications 110-120Volt, 60 Hz. Tool InformationProperly Prong Plug Grounded Prong Outlet Make sure this Motor Specifications and Electrical Wire SizesExtension Wire Sizes Required Cord Length For A.W.G Requirements Contents Unpacking and Checking Contents List LooseParts Loose Parts Installing Handwheels and Bevel Pointer Assembling Steel Legs Mounting Your Saw Leg Set Flat WasherBench Mounting Assembly Assembling Table Extensions Installing Rip Fence Guide Bars and Switch Hex Nuts Lockwashers Lockwas her Wire Tie Aligning ExtensionsCould be hit or cut Extension Checking Table Insert Leveling Tab Edge Installing Blade Guard Port AndBracket To On-Off Switch Getting to Know Your Table SawRip Fence Exacti-Cut Table Insert Tilt Handwheel Elevation Handwheel Lock Knob Removing and Installing Sawblade Push To Tighen Safety Instructions for Basic Saw Operations Before Each UseInspect your saw Inspect Your Blade Planyour cut Avoid Accidental StartingDont Force Tool Work Feed Devices Push StickPush Block Auxiliary Fence Making the handle3E-l!2rL Thick Plywood Base Thick Side Plywood Finished Auxiliary Fence Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations Crosscutting Crosscutting Miter Crosscutting Bevel CrosscuttingCompound Crosscutting Using the Rip Fence Additional Safety instructions for Rip CutsRipping Always Support Long Or Wide Workpieces Push Block Using Featherboards for Thru-Sawing Bevel Ripping Narrow WorkWork Featherhoar Facing Using Featherboards for Non Thru-Sawing ResawingWork Sup Ond pass LcelSaeJ ArborFence Making Adjustments Mended accessoriesPloughing and Molding Molding Cutting Self Aligning Spring Adjustment Rip Fence Rip Fence Alignment Adjustment Adjusting Rip Scale IndicatorSlide Spring To Adjust Pressure Lock Handle To check for parallelism 3t16Locking screws Wrench Pointer Adjusting Screw Blade Tilt, or Squareness of Blade to Table With Piece Blade Elevation Tilt and Elevation MechanismTilt Screw Screws Maintenance Maintaining Your Table Saw Lubrication Pivot Nut Sears Recommends the Following Accessories Remedy Probable Cause Into blade Repair Parts Parts List for Craftsman 10 Inch Fable Saw Model No Parts List for Craftsman 10 Inch Table Saw Model No 201 Parts List for Craftsman 10 Inch Table Saw Model No. t Description Parts list for Craftsman 10 Inch Table Saw 201!17 Parts List for Craftsman 10 Inch Table Saw Model Key Pad No Description Repair Parts Parts List for Craftsman 10 Inch Table Saw Model Model No Rear Guide Bar RefKey Key j Foot Leveling For the repair or replacement paris you need For in-home major brand repair serviceSears, Roebuck Co., Hoffman Estates, IL U.S.A