Getting to Know Your Table Saw, On-Off Switch | Craftsman 113.29921

Getting to Know Your Table Saw	......
8 Sawblade	6 Blade Guard
5 Miter Gauge	4 Rip Fence
	4 Rip Fence

9 Exacti-Cut

7 Table Insert

3Tilt

Handwheel

2Elevation Handwheel

Switch

1, On-Off Switch.

the blade guard is correctly installed and operat- I CAUTtON: Before turning switch "ON", make sure

ing properly.

The On-Off Switch has a locking feature_ This feature is intended to help prevent unauthorized and possible haz- ardous use by children and others

A Remove key from bag labeled "Miscellaneous" and insert into switch.

B To turn saw ON, stand to either side of the bJade, never in line with it, insert finger under switch lever and pull end of lever out

After turning switch ON, always allow the blade to© come up to full speed before cutting. Do not cycle

the motor switch on and off rapidly, as this may cause the sawblade to loosen. In the event this should ever occur, allow the sawbIade to come to a complete stop and retighten the arbor nut normally, not excessively Never leave the saw while the power is "ON"

CTo turn saw OFF, PUSH lever in Never leave the saw until the cutting too} has come to a complete stop

D To lock switch in OFF position, hold switch IN with one hand, REMOVE key with other hand

WARNING: For your own safety, lower blade or other cutting tool below table surface. (if blade is tilted, return it to vertical, 90 °, position.) Always lock the switch "OFF". When saw is not in use, remove key and keep it in a safe place. Also, in the event of a power failure (all of your lights go out) turn switch off, lock it and remove the key. This will prevent the saw from starting up again when the power comes back on.

21

Image 21

Craftsman 113.29921 owner manual Getting to Know Your Table Saw, On-Off Switch, Rip Fence, Ing properly

Contents

Rip Fence Miter Gauge Two Table ExtensionsSears, Roebuck and Co., Hoffman Estates, IL US,A Save This Manual For Future Reference Safety Signal Words Before Using The Saw Safety Instructions For Table SawWhen Installing Or Moving The Saw Sears, Roebuck and Co, D/817 WA Hoffman Estates, IL Before Each Use Dress for safety Safety Instructions For Table SawsPlan Ahead To Protect Your Eyes, Hands, Face and Ears Whenever Sawblade Is Spinning While Thru-sawing Additional Safety InstructionsGrain Featherboard Glossary of Terms for Woodworking Miter CutMolding 110-120Volt, 60 Hz. Tool Information Motor SpecificationsProperly Prong Plug Grounded Prong Outlet Make sure this Wire Sizes Motor Specifications and ElectricalExtension Wire Sizes Required Cord Length For A.W.G Requirements Contents Unpacking and Checking Contents Loose ListParts Loose Parts Assembling Steel Legs Installing Handwheels and Bevel Pointer Mounting Your Saw Leg Set Flat WasherBench Mounting Assembling Table Extensions Assembly Installing Rip Fence Guide Bars and Switch Lockwas her Hex Nuts Lockwashers Aligning Extensions Wire TieCould be hit or cut Extension Leveling Tab Edge Checking Table Insert Installing Blade Guard Port AndBracket To Getting to Know Your Table Saw On-Off SwitchRip Fence Exacti-Cut Table Insert Tilt Handwheel Elevation Handwheel Lock Knob Push To Tighen Removing and Installing Sawblade Before Each Use Safety Instructions for Basic Saw OperationsInspect your saw Inspect Your Blade Planyour cut Avoid Accidental StartingDont Force Tool Work Feed Devices Push StickPush Block Making the handle Auxiliary Fence3E-l!2rL Thick Plywood Base Thick Side Plywood Finished Auxiliary Fence Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations Crosscutting Crosscutting Miter Crosscutting Bevel CrosscuttingCompound Crosscutting Additional Safety instructions for Rip Cuts Using the Rip FenceRipping Always Support Long Or Wide Workpieces Push Block Bevel Ripping Narrow Work Using Featherboards for Thru-SawingWork Featherhoar Facing Resawing Using Featherboards for Non Thru-SawingWork Sup Ond pass Arbor LcelSaeJFence Making Mended accessories AdjustmentsPloughing and Molding Molding Cutting Rip Fence Self Aligning Spring Adjustment Adjusting Rip Scale Indicator Rip Fence Alignment AdjustmentSlide Spring To Adjust Pressure Lock Handle 3t16 To check for parallelismLocking screws Wrench Blade Tilt, or Squareness of Blade to Table Pointer Adjusting Screw With Piece Tilt and Elevation Mechanism Blade ElevationTilt Screw Screws Maintaining Your Table Saw Maintenance Pivot Nut Lubrication Remedy Sears Recommends the Following Accessories Into blade Probable Cause Parts List for Craftsman 10 Inch Fable Saw Model No Repair Parts 201 Parts List for Craftsman 10 Inch Table Saw Model No Description Parts List for Craftsman 10 Inch Table Saw Model No. t 201!17 Parts list for Craftsman 10 Inch Table Saw Key Pad No Description Parts List for Craftsman 10 Inch Table Saw Model Repair Parts Model Parts List for Craftsman 10 Inch Table Saw Model No Rear Guide Bar RefKey Foot Leveling Key j For in-home major brand repair service For the repair or replacement paris you needSears, Roebuck Co., Hoffman Estates, IL U.S.A