NON-THROUGH Cuts, Non-Throughcut | Craftsman 315.22038 specs

NON-THROUGH CUTS

See Figure 49.

WARNING: Unplug the saw while removing or replacing the blade guard. Tum on the saw with

the switch on the arm to confirm the blade is not receiving power.

•Remove the blade and blade guard (see Assembly section).

•Place a support the same height as the saw table nearby for the cut work. Lower the blade with the elevating handwheel.

•Make sure the wood is not touching the blade, Insert the key and turn on the saw, Let the blade build up to full speed before contacting the work- piece.

_1= WARNING: Always use pushblocks when making non-through rip cuts to avoid the risk of

serious injury, Never feed wood with your hands.

•When the work is completed, press the switch off and remove the key.

NON-THROUGHCUT

Fig. 49

53CRRFI"SNRIrRADIALSAW315.220380

Image 53

Craftsman 315.22038 owner manual NON-THROUGH Cuts, Non-Throughcut

Contents

OwnersManual Full ONE Year Warranty on Craftsman Radial ARM SAW CliaFTtHIIIr RADIALSAW315.220380 Read ALL Instructions Safety Alert Symbol Avoid Awkward Operations and Hand Never USE this Tool in AN Explosive Be Sure the Blade Clears the Work Page Electrical Connection Extension CordsGrounding Instructions PIN Coverof Grounded Outletbox See Figures Assembly sectionChanging Voltage CRRFTSMRWRADIALSAW315.22038010 Resin Sticky,sap-basedsubstance SAW Assemblyshownas Packed Cdef CtorDE Oo0 Framingsquare 15RIIFTIMRNRADIALSAW315.220380 RRFTMRNRADIALSAW315.22038016 FtsmanreplacementpartsSerno 17CRAFTSMANRADIALSAW315.220380 Advertencia See a Know Your Radial SAWMethod Yoke Control See Figures 9A-9D Featureslist Figures 9A and 9B Dustguide Holddown Downknob Upper Bladeguard Lower MOTOR13/6.5AMP- Powersthe blade and is See Figures 10,4 10C Hexnut Elevating Shaft Handwheel Screw Starwasher Mounting SAW to LEG Stand Armviewedfrombelow Clockwasher Installing the Yoke AssemblyArmlockknob Carriagearm Lockknob CAP Screws Attaching Table Supports Removing the BladeSee Figure Leveling The Table Supports section RAFTSMANRADIALSAW315.22038026 Setting the ARM Lock KnobYokelock Handle Bevellockleverin Correctlockedposition Setting the Bevel Lock LeverStarwasher Socketscrew Bevel Locklever Tube Column Support Tightening the ARM and Column Rotation Adjustment Elevation AdjustmentColumn Silverblack Screws Columnsupport CAP Screws 29RRFTSMIWRADIALSAW315,220380 See Figures 21A and 21B Adjusting the Carriage BearingsCarriagebearing Eccentricscrew Wrench Graspand Hold Carriagebearing Blade Wrenchat Front Armlock Knob Bevel Indexknob Leveling the Table Supports Hexnut Installing the Front TableSetscrew If there are any high or low areas on the front table Leveling the Front Table Washer Hole AssembledSupport CUP To Washer Loosen Thumbscrew Bladeguard Screwand NUT Rivingknifebladenut Blade Tighten Align Riving Knife to Blade Spring Carriage Screws Lockknob Installing RIP Scale Indicators ScrewsRIP Scale Indicator Carriage Speednut Elevating Handwheel Straight Edge Framing Square Thereshouldbeno Gapherewhen Aligning Blade to Table AT Obevel Bladesquaretotable Noadjustmentneeded Framing SquareSee Figures 3OA 30D ARM Lockknob Indexcap Squaring Blade to Fence SAW Viewed From Above Blade Square Adjustment BladeSee Figures 31A 31C Armlockknob See Figures 32A-32C Adjustment GAPParalleling Blade to Table IN-RIPSCALEON Rightsideof ARM RIP-SCALEINDICATOR Aligning the RIP Scale IndicatorsOUT-RIPSCALEONLEFTSIDE of ARM RIP-SCALEINDICATOR Carriagelockknob Barrel Carriage Assembly Installing Control CUT Device Types of Cuts Basic Operation of the Radial ARM SAWCrosscuts RIP Cuts Insertswitchkey Switchon Switchoff Switch and Switch KEYCauses of Kickback Avoiding Kickback Pushsticks Cutting AidsPushblocks Featherboards Making a Cross CUT Switch BevelCarriage Lockknob Tableclamps Crosscut Rivingknife Elevating Handwheel Ercut Elevating Handwheel Making a Miter CUT Making a Bevel CUT Switch Handleyokelock Riving Elevating Handwheel Beveledand Elevating Handwheel Making a Compound Cross CUT Setting UP a RIP CUT RIP CUT Hazards and PrecautionsSwitch Elevating Infeedfor OUT RIP Cutting Blade Switch ANTI-KICKBACK PawlsMaking a RIP CUT See Making Oher CutsCutting Long Workpieces Supportlongworkpieces IRAFTNIINRADIALSAW315.22038052 NON-THROUGHCUT NON-THROUGH Cuts MOTOR/ELECTRICAL General Maintenance Solution Problem Cause Problem Cause Solution 57CRRFTSMANRADIALSAW315.220380 Problem CausesolutionSee Adjusting the Column Tube in Assembly section Arm Lock ProblemSee Squaring the Blade to Fence in Adjustments section Cause SolutionSee Adjusting the Column Tube in Assembly section Craftsman Radial ARM SAW Model no Seergurei KEY Part NO. Number Craftsman Radial ARM SAW- Model noDescription Quan KEY Part Figure B See Figure KEY Part Number Craftsman Radial ARM SAW Model no .22038Q Figure C Radial ARM SAW Model no Craftsman Radial ARM SAW Model no Parts List for Figure C Craftsman Radial ARM SAW Model no Keypart NO.NUMBER Parts List for Figure O Rgure E Craftsman Radial ARM SAW- Model no 69CRRFTSMBWRADIALSAW315.220380 Craftsman Radial ARM SAW- Model no Craftsman RADIAL-ARM SAW Model no Seefigureg Description Parts List for Figure F See Figure F Figure G 73RRFTSMIINRADIALSAW315.220380 Craftsman Radial ARM SAW Model no Figure H KEY Part Number Description Parts List for Figure H 11 9 Parts List for Figure Rgure J Seergurek Parts List for Figure J Figure K Parts List for Figure K PartsDirect