Manuals / Craftsman / Power Tools / Saw

Craftsman Repair Parts, PARTS LIST CRAFTSMAN 10 RADIAL SAW GUARD KIT #509398 & #509399, 3 12

Models: 509398

1 52

Download 52 pages 43.04 Kb

Page 50

Image 50

PARTS LIST CRAFTSMAN 10" RADIAL SAW GUARD KIT

#509398 & #509399

Always order by Part Number - Not by Key Number

Figure 2

9	31	31
	31	32
		32

Repair Parts

28	17
27	16
	22

3 12 13

		15	13	14
		15	3
		21
		20
	23	19
26	24	18
		25

Page 50

Image 50

Craftsman owner manual Repair Parts, PARTS LIST CRAFTSMAN 10 RADIAL SAW GUARD KIT #509398 & #509399, 3 12

Contents

MODEL NO 509398 509399 509398 FITS THE FOLLOWING RADIAL SAWS owner’s manual10-INCH RADIAL SAW GUARD KIT 509399 FITS THE FOLLOWING RADIAL SAWSPage Table of ContentsSection Title Major Hazards SafetySafety Symbol and Signal Words Read and follow all safety information and instructionsRead and follow the information and instructions under ripping safety SafetyRead and follow the information and instructions under ripping safety Kickback HazardGuard Features Include Guard Function and FeaturesSafety TO AVOID INJURY SHUT OFF POWER BEFORE CLEARING A JAMMED LOWER GUARD Hazards Associated with Clear Por- tion of GuardSafety Clear plastic guard will increase risk of certain hazardsWork Area Safety Instructions Safety InstructionsPersonal Safety Instructions SafetySafety Saw Safety InstructionsWorkpiece Safety Instructions Blade Safety Instructions SafetyOn-Product Safety Labels SafetyOn the clear plastic guard is this OSHA required label Safetysee Accessories Section List of loose parts with model AssemblyIdentify Parts List of loose parts with modelAssembly Remove Sawblade and GuardRemove Original Table Boards, and Mounting Supports Do not plug in saw at any time during assemblyAssembly Attaching Table SupportsPositioning Table Supports Installing Front Table AssemblyAssembly Make Front Table FlatInstalling Table Boards 44 Wide Models Installing Front Table AssemblyLeveling Front Table AssemblyAssembly 5. Lock the bevel lock to hold the motor in this positionMaking Front Table Flat Assembly1/2 x 13 Lock Nut AssemblyMotor Assembly #8 Plastite Screws Motor Support Cap Not on all models Yoke Cover Bevel SpringAssembly a. Shaft supportAssembly If motor does not index securely, the adjust- ment is too looseTop Motor Cover Screw Motor Cover Panel Adapter Installing Guard AdapterAssembly Framing Square Must Be True Installing Blade/Squaring Crosscut TravelAssembly Assembly Install Fence, Rear Tables, and Table ClampsInstall Guard Guard Installation Steps/Align Riving Knife to Blade AlignmentRequires yellow key ControlsHold in unlocked position while mov- ing arm Hold in unlocked position while mov- ing blade carriage ControlsLock before ripping Frees carriage to move along radialDust Elbow Guard Clamp Screw ControlsProtects against contact with upper GuardPawls/Riving Knife Knob Guard Tab Pawls Riving Knife ControlsProvides manual way to raise clear Crosscutting Defined CrosscuttingCrosscutting Safety Exposed Blade TeethKeep one hand on saw handle through step CrosscuttingCrosscut Kerfs Keep one hand on saw handle through step CrosscuttingMaking Crosscuts Keep hand holding down workpiece at least 8 from blade CrosscuttingRepetitive Crosscutting Crosscutting HintsIn-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed DirectionsWorkpiece Positioning Ripping SafetyRipping Push Sticks and Push BlocksOutfeed Zone Hazard DANGERRipping KickbackWrong Way Feed RippingTo reduce risk of kickback To eliminate risk of wrong way feedPawls and Riving Knife Function RippingHold Down Function use out-rip position for rips 16 or wider Ripping Set-up ProcedureRipping against blade.** Note Workpiece will be between blade and table frontBevel the edge that is not against the fence RippingSpecial Notes for Bevel Set-Up Making Rip CutsOut-Ripping RippingRelease tab as soon as clear guard rests on workpiece In-RippingEdging RippingDado Blades, Molding Heads Ripping HintsPush Block Cutting AidesPush Sticks Push StickPutting it together Cutting AidesMaking the Handle Auxiliary Fencea place irregular side of workpiece against fence Cutting AidesStraight Edge for Irregular Workpiece b put straight-edged board on top of work- piece and against fence1. Clean sawdust from the slot and slider MaintenanceLubricating Blade Guard Assembly Replacing PawlsDescription Repair PartsPARTS LIST CRAFTSMAN 10 RADIAL SAW GUARD KIT #509398 & #509399 Always order by Part Number - Not by Key Number Repair PartsPARTS LIST CRAFTSMAN 10 RADIAL SAW GUARD KIT #509398 & #509399 3 12Always order by Part Number - Not by Key Number FIGURE 2 - GUARD Repair PartsPARTS LIST CRAFTSMAN 10 RADIAL SAW GUARD KIT #509398 & #509399 DescriptionMODEL NO 509398 509399 10-INCH RADIAL SAWGUARD KIT RZQHU·V