Cypress CY14B104K, CY14B104M manual 0x7FFF2 0x3FFF2 Alarm Seconds, Centuries 0x7FFF0 0x3FFF0 Flags

PRELIMINARY

CY14B104K, CY14B104M

Table 5. Register Map Detail (continued)

Register

Description

CY14B104K

CY14B104M

0x7FFF4

0x3FFF4

Alarm - Hours

D7

D6

D5

D4

D3

D2

D1

D0

M

10s Alarm Hours

Alarm Hours

Contains the alarm value for the hours and the mask bit to select or deselect the hours value.

M

Match. When this bit is set to 0, the hours value is used in the alarm match. Setting this bit to 1

causes the match circuit to ignore the hours value.

0x7FFF3

0x3FFF3

Alarm - Minutes

D7

D6

D5

D4

D3

D2

D1

D0

M

10s Alarm Minutes

Alarm Minutes

Contains the alarm value for the minutes and the mask bit to select or deselect the minutes value.

M

Match. When this bit is set to 0, the minutes value is used in the alarm match. Setting this bit to 1

causes the match circuit to ignore the minutes value.

0x7FFF2

0x3FFF2

Alarm - Seconds

D7

D6

D5

D4

D3

D2

D1

D0

M

10s

Alarm Seconds

Alarm Seconds

Contains the alarm value for the seconds and the mask bit to select or deselect the seconds’ value.

M

Match. When this bit is set to 0, the seconds value is used in the alarm match. Setting this bit to

1 causes the match circuit to ignore the seconds value.

0x7FFF1

0x3FFF1

Time Keeping - Centuries

D7

D6

D5

D4

D3

D2

D1

D0

10s

Centuries

Centuries

Contains the BCD value of centuries. Lower nibble contains the lower digit and operates from 0

to 9; upper nibble contains the upper digit and operates from 0 to 9. The range for the register is

0-99 centuries.

0x7FFF0

0x3FFF0

Flags

D7

D6

D5

D4

D3

D2

D1

D0

WDF

AF

PF

OSCF

0

CAL

W

R

WDF

Watchdog

Timer Flag.

This read only bit is set to 1 when the watchdog timer is allowed to reach

0 without being reset by the user. It is cleared to 0 when the Flags register is read or on power up

AF

Alarm Flag. This read only bit is set to 1 when the time and date match the values stored in the

alarm registers with the match bits = 0. It is cleared when the Flags register is read or on power up.

PF

Power Fail Flag. This read only bit is set to 1 when power falls below the power fail threshold

VSWITCH. It is cleared to 0 when the Flags register is read or on power up.

OSCF

Oscillator Fail Flag. Set to 1 on power up if the oscillator is enabled and not running in the first 5

ms of operation. This indicates that RTC backup power failed and clock value is no longer valid.

This bit survives power cycle and is never cleared internally by the chip. The user must check for

this condition and write '0' to clear this flag.

CAL

Calibration Mode. When set to 1, a 512 Hz square wave is output on the INT pin. When set to 0,

the INT pin resumes normal operation. This bit defaults to 0 (disabled) on power up.

W

Write Enable: Setting the W bit to 1 freezes updates of the RTC registers. The user can then write

to RTC registers, Alarm registers, Calibration register, Interrupt register and Flags register. Setting

the W bit to 0 causes the contents of the RTC registers to be transferred to the time keeping

counters if the time has been changed (a new base time is loaded). This bit defaults to 0 on power

up.

R

Read Enable: Setting R bit to 1, stops clock updates to user RTC registers so that clock updates

are not seen during the reading process. Set R bit to 0 to resume clock updates to the holding

register. Setting this bit does not require W bit to be set to 1. This bit defaults to 0 on power up.

Document #: 001-07103 Rev. *K

Page 13 of 31

[+] Feedback