PRELIMINARY | CY14B104K, CY14B104M |
|
New time out values are written by setting the watchdog write bit to ‘0’. When the WDW is ‘0’, new writes to the watchdog time out value bits
The output of the watchdog timer is the flag bit WDF that is set if the watchdog is allowed to time out. If the Watchdog Interrupt Enable (WIE) bit in the Interrupt register is set, a hardware interrupt on INT pin is also generated on watchdog timeout. The flag and the hardware interrupt are both cleared when user reads the Flags registers.
Figure 3. Watchdog Timer Block Diagram
Oscillator |
| Clock |
| 1 Hz | |
| Divider |
| |||
|
|
|
| ||
32,768 KHz |
|
| 32 Hz |
|
|
|
|
|
|
| |
|
|
|
|
|
|
determine the cause of the interrupt. The INT pin driver has two bits that specify its behavior when an interrupt occurs.
An Interrupt is raised only if both a flag is raised by one of the three sources and the respective interrupt enable bit in Interrupts register is enabled (set to ‘1’). After an interrupt source is active, two programmable bits, H/L and P/L, determine the behavior of the output pin driver on INT pin. These two bits are located in the Interrupt register and can be used to drive level or pulse mode output from the INT pin. In pulse mode, the pulse width is internally fixed at approximately 200 ms. This mode is intended to reset a host microcontroller. In the level mode, the pin goes to its active polarity until the Flags register is read by the user. This mode is used as an interrupt to a host microcontroller. The control bits are summarized in the following section.
Interrupts are only generated while working on normal power and are not triggered when system is running in backup power mode.
Note CY14B104K generates valid interrupts only after the Powerup Recall sequence is completed. All events on INT pin must be ignored for tHRECALL duration after powerup.
WDS
WDW
Counter
Load
Register
DQ
Q
Zero
Compare
WDF
Interrupt Register
Watchdog Interrupt Enable - WIE. When set to ‘1’, the watchdog timer drives the INT pin and an internal flag when a watchdog time out occurs. When WIE is set to ‘0’, the watchdog timer only affects the WDF flag in Flags register.
Alarm Interrupt Enable - AIE. When set to ‘1’, the alarm match drives the INT pin and an internal flag. When AIE is set to ‘0’, the alarm match only affects the AF Flags register.
| Watchdog |
write to | Register |
Watchdog |
|
Register |
|
.
Power Monitor
The CY14B104K provides a power management scheme with power fail interrupt capability. It also controls the internal switch to backup power for the clock and protects the memory from low VCC access. The power monitor is based on an internal band gap reference circuit that compares the VCC voltage to VSWITCH threshold.
As described in the section “AutoStore Operation” on page 3, when VSWITCH is reached as VCC decays from power loss, a data STORE operation is initiated from SRAM to the nonvolatile elements, securing the last SRAM data state. Power is also switched from VCC to the backup supply (battery or capacitor) to operate the RTC oscillator.
When operating from the backup source, read and write opera- tions to nvSRAM are inhibited and the clock functions are not available to the user. The clock continues to operate in the background. The updated clock data is available to the user tHRECALL delay after VCC is restored to the device (see “AutoStore/Power Up RECALL” on page 20)
Interrupts
The CY14B104K has Flags register, Interrupt register, and Interrupt logic that can signal interrupt to the microcontroller. There are three potential sources for interrupt: watchdog timer, power monitor, and alarm timer. Each of these can be individually enabled to drive the INT pin by appropriate setting in the Interrupt register (0x7FFF6). In addition, each has an associated flag bit in the Flags register (0x7FFF0) that the host processor uses to
Document #:
Power Fail Interrupt Enable - PFE. When set to ‘1’, the power fail monitor drives the pin and an internal flag. When PFE is set to ‘0’, the power fail monitor only affects the PF flag in Flags register.
High/Low - H/L. When set to a ‘1’, the INT pin is active HIGH and the driver mode is push pull. The INT pin drives high only when VCC is greater than VSWITCH. When set to a ‘0’, the INT pin is active LOW and the drive mode is open drain. The INT pin must be pulled up to Vcc by a 10k resistor while using the interrupt in active LOW mode.
Pulse/Level - P/L. When set to a ‘1’ and an interrupt occurs, the INT pin is driven for approximately 200 ms. When P/L is set to a ‘0’, the INT pin is driven high or low (determined by H/L) until the Flags or Control register is read.
When an enabled interrupt source activates the INT pin, an external host reads the Flags registers to determine the cause. Remember that all flags are cleared when the register is read. If the INT pin is programmed for Level mode, then the condition clears and the INT pin returns to its inactive state. If the pin is programmed for Pulse mode, then reading the flag also clears the flag and the pin. The pulse does not complete its specified duration if the Flags register is read. If the INT pin is used as a host reset, the Flags register is not read during a reset
Flags Register
The Flag register has three flag bits: WDF, AF, and PF, which can be used to generate an interrupt. They are set by the watchdog timeout, alarm match, or power fail monitor respectively. The processor can either poll this register or enable interrupts when a flag is set. These flags are automatically reset once the register is read. The flags register is automatically loaded with the value 0x00 on power up (except for the OSCF bit. See “Stopping and Starting the Oscillator” on page 6.)
Page 8 of 31
[+] Feedback
