Cypress CY7C1387F, CY7C1386F, CY7C1386D manual Features, Selection Guide, MHz 200 MHz 167 MHz Unit

CY7C1386D, CY7C1386F

CY7C1387D, CY7C1387F

18-Mbit (512K x 36/1 Mbit x 18) Pipelined DCD Sync SRAM

Features Functional Description [1]

•Supports bus operation up to 250 MHz

•Available speed grades are 250, 200, and 167 MHz

•Registered inputs and outputs for pipelined operation

•Optimal for performance (double-cycle deselect)

•Depth expansion without wait state

•3.3V core power supply (VDD)

•2.5V or 3.3V IO power supply (VDDQ)

•Fast clock-to-output times

— 2.6 ns (for 250 MHz device)

•Provides high-performance 3-1-1-1 access rate

•User selectable burst counter supporting Intel→ Pentium→ interleaved or linear burst sequences

•Separate processor and controller address strobes

•Synchronous self timed writes

•Asynchronous output enable

•CY7C1386D/CY7C1387D available in JEDEC-standard Pb-free 100-pin TQFP, Pb-free and non Pb-free 165-ball FBGA package. CY7C1386F/CY7C1387F available in Pb-free and non Pb-free 119-ball BGA package

•IEEE 1149.1 JTAG-Compatible Boundary Scan

•ZZ sleep mode option

Selection Guide

The CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F SRAM integrates 512K x 36/1M x 18 SRAM cells with advanced synchronous peripheral circuitry and a two-bit counter for internal burst operation. All synchronous inputs are gated by registers controlled by a positive edge triggered clock input (CLK). The synchronous inputs include all addresses, all data inputs, address-pipelining chip enable (CE1), depth expansion chip enables (CE2 and CE3 [2]), burst control inputs (ADSC, ADSP, and ADV), write enables (BWX, and BWE), and global write (GW). Asynchronous inputs include the output enable (OE) and the ZZ pin.

Addresses and chip enables are registered at rising edge of clock when either address strobe processor (ADSP) or address strobe controller (ADSC) are active. Subsequent burst addresses can be internally generated as controlled by the advance pin (ADV).

Address, data inputs, and write controls are registered on-chip to initiate a self timed write cycle.This part supports byte write operations (see Pin Configurations on page 3 and Truth Table [4, 5, 6, 7, 8] on page 9 for further details). Write cycles can be one to four bytes wide as controlled by the byte write control inputs. GW active LOW causes all bytes to be written. This device incorporates an additional pipelined enable register which delays turning off the output buffers an additional cycle when a deselect is executed.This feature allows depth expansion without penalizing system performance.

The CY7C1386D/CY7C1387D/CY7C1386F/CY7C1387F operates from a +3.3V core power supply while all outputs operate with a +3.3V or +2.5V supply. All inputs and outputs are JEDEC-standard and JESD8-5-compatible.

	250 MHz	200 MHz	167 MHz	Unit
Maximum Access Time	2.6	3.0	3.4	ns
Maximum Operating Current	350	300	275	mA
Maximum CMOS Standby Current	70	70	70	mA

Notes

1.For best practices or recommendations, please refer to the Cypress application note AN1064, SRAM System Design Guidelines on www.cypress.com.

2.CE3 and CE2 are for TQFP and 165 FBGA packages only. 119 BGA is offered only in Single Chip Enable.

Cypress Semiconductor Corporation	•	198 Champion Court • San Jose, CA 95134-1709	•	408-943-2600
Document Number: 38-05545 Rev. *E		Revised Feburary 09, 2007

[+] Feedback