CY7C1441AV33
CY7C1443AV33,CY7C1447AV33
Document #: 38-05357 Rev. *G Page 10 of 31
ZZ Mode Electrical CharacteristicsParameter Description Test Conditions Min. Max. Unit
IDDZZ Sleep mode standby current ZZ > VDD – 0.2V 100 mA
tZZS Device operation to ZZ ZZ > VDD – 0.2V 2tCYC ns
tZZREC ZZ recovery time ZZ < 0.2V 2tCYC ns
tZZI ZZ active to sleep current This parameter is sampled 2tCYC ns
tRZZI ZZ Inactive to exit sleep current This parameter is sampled 0 ns
Truth TabletThe truth table for CY7C1441AV33/CY7C1443AV33/CY7C1447AV33 follows.[2, 3, 4, 5, 6]
Cycle Description ADDRESS
Used CE1CE2CE3ZZ ADSP ADSC ADV WRITE OE CLK DQ
Deselected Cycle, Power down None H X X L X L X X X L-H Tri-State
Deselected Cycle, Power down None L L X L L X X X X L-H Tri-State
Deselected Cycle, Power down None L X H L L X X X X L-H Tri-State
Deselected Cycle, Power down None L L X L H L X X X L-H Tri-State
Deselected Cycle, Power down None X X X L H L X X X L-H Tri-State
Sleep Mode, Power down None X X X H X X X X X X Tri-State
Read Cycle, Begin Burst External L H L L L X X X L L-H Q
Read Cycle, Begin Burst External L H L L L X X X H L-H Tri-Stat e
Write Cycle, Begin Burst External L H L L H L X L X L-H D
Read Cycle, Begin Burst External L H L L H L X H L L-H Q
Read Cycle, Begin Burst External L H L L H L X H H L-H Tri-State
Read Cycle, Continue Burst Next X X X L H H L H L L-H Q
Read Cycle, Continue Burst Next X X X L H H L H H L-H Tri-State
Read Cycle, Continue Burst Next H X X L X H L H L L-H Q
Read Cycle, Continue Burst Next H X X L X H L H H L-H Tri-State
Write Cycle, Continue Burst Next X X X L H H L L X L-H D
Write Cycle, Continue Burst Next H X X L X H L L X L-H D
Read Cycle, Suspend Burst Current X X X L H H H H L L-H Q
Read Cycle, Suspend Burst Current X X X L H H H H H L-H Tri-State
Read Cycle, Suspend Burst Current H X X L X H H H L L-H Q
Read Cycle, Suspend Burst Current H X X L X H H H H L-H Tri-State
Write Cycle, Suspend Burst Current X X X L H H H L X L-H D
Write Cycle, Suspend Burst Current H X X L X H H L X L-H D
Notes
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
3. WRITE = L when any one or more Byte Write enable signals and BWE = L or GW = L. WRITE = H when all Byte write enable signals, BWE, GW = H.
4. The DQ pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BWX. Writes may occur only on subsequent clocks after
the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a don't care
for the remainder of the write cycle.
6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is inactive
or when the device is deselected, and all data bits behave as output when OE is active (LOW).
[+] Feedback