DES-5200 Rear Panel | D-Link manual

Fast Ethernet Switching System User’s Guide

Rear Panel

The three pronged power plug, ventilation fan and the on/off switch are located at the rear of the DES-5200, displayed in Figure 4. The switch will work with AC in the range 100-240 VAC, 50-60 Hz. The power requirements are indicated on the rear panel of the DES-5200. When installing the DES-5200, leave enough room to enable you to plug in the power cable.

There are heat vents located on the sides. The fans and the vents help to cool the DES-5200. Always leave two inches of space around the DES-5200 to that air can circulate and cool the DES-5200.

Fan

Power On/Off switch

Three pronged power plug

Figure 4: DES-5200 Rear Panel

Introduction

8

Image 15

D-Link manual DES-5200 Rear Panel

Contents

DES-5200 Fast Ethernet Switching System User’s Guide Software Limited WarrantyLink Offices for Registration and Warranty Service Hardware Europe and Israel Wichtige Sicherheitshinweise Table of Contents Web Management 125 Organization Audience Introduction Features Fast Ethernet Switching System User’s Guide Models Front Panel Optional Modules Full Size Modules DES-5220TF DES-5224TX DES-5216FX DES-5216FX.A1 DES-5200 Rear Panel Rear Panel Management Methods Software Update Unpacking the DES-5200 Installing the DES-5200 Installation Options Install Feet on Bottom Desktop/ Shelf Installation Attach Feet Attach Mounting Brackets Rack Installation Insert into Rack Installing Optional Modules Remove Blank Bracket Insert Optional Module Power On Copper Cable Cable Specifications 10BASE-T Cable Diagram Fiber Optic Cable RS-232 Port PortsMDI-X Ports Fiber Optic Ports DES-5200 to DES-5200 Connection Connecting the DES-5200 to other Switches and Hubs LEDs Status PowerDiagnostic CPU Module LED Port 10/100-TX Module LinkDuplex FDX 100/10 Col Port FX Module Link/ActFull/Half Port 100BASE-FX Module Port 100BASE-FX Module FX Module LED Act Port 1000BASE-SX Module Console Based Management ∙ Parity None ∙ Stop bits ∙ Flow Control Xon/Xoff Console Management Telnet Management Configuring Through the Ethernet Port Log ∙ Default User Name D-Link ∙ Default Password D-Link Help Message Help Message Spacebar Panel Conventions Console Program System ConfigurationSwitch Port Configuration Spanning Tree Configuration Port Statistics Snmp Management ConfigurationVlan Port Management Trunking Port Management System Information System Configuration MenuSystem Reset Factory Reset to Default Config Values Hardware Revision Software UpdateBoot Prom Firmware Version System Information Menu System Name LAN Default GatewayMAC Address System Description System Reset Factory Reset Factory Reset Disadvantages of Store and Forward Advantages of Store and Forward Disadvantages of Cut-Through Advantages of Cut-Through Software Update Configuration Software Update Menu Software Update Confirmation Send File Xmodem Tftp Tftp Transfer Complete User Account Change Menu User Account Management Create New User PasswordConfirm Password Access Level Fast Ethernet Switching System User’s Guide Delete Delete Users Fast Ethernet Switching System User’s Guide Change Password Old PasswordNew Password Select Save and press Enter to save your changes Switch Port Configuration Switch Port Configuration Menu StatePhysical Priority Port State Spanning Tree Algorithm Spanning Tree ConfigurationSpanning Tree Configuration Menu STA Operation Levels Hello Time Forward Delay TimeBridge Priority Root Cost Root Port Root Bridge Snmp Management Configuration Snmp Community String Snmp Management Configuration MenuSnmp Manager Setting Access Right Link Change Event Snmp Trap Manager SettingAuthentication Failure Cold Start Status Vlan Port Management Vlan Port Management menu Vlan Port Management Menu TrunkGroup Create New VlanNew Vlan Name Port # Fast Ethernet Switching System User’s Guide Vlan Name Delete Vlan Menu Virtual LAN Name Modify Vlan Menu Trunking Port Management menu Trunking Port Management Menu Create New Trunking Port New Trunking Group NameName Fast Ethernet Switching System User’s Guide Trunking Port Delete Trunking Port Trunking Port Name Modify Trunking Port Port Statistics Rx Error Oversized TX FCS ErrorsTx Run Errors Rx Align or FCS Errors Rx65 to Rx Error UndersizedRx Good Undersized Rx64 Refresh Using Web ManagementCommands Apply Logging User Name and Password System Configuration System Information Software Version Boot Prom Firmware VersionSystem Information Menu Hardware Revision System Name LAN Default GatewayMAC Address System Description System Reset Factory Reset Factory Reset Confirmation System Rate Control Disadvantages of Store and Forward Software Update Web Management 101 Software Download Download Successful Web Management 104 Change Password Web Management 106 Switch Port Configuration Confirmation Web Management 108 Spanning Tree Configuration Web Management 110 Web Management 111 Web Management 112 Web Management 113 Snmp Manager Setting Snmp Trap Manager Setting Snmp Trap Manager Setting ∙ Cold Start ∙ Authentication Failure ∙ Link Change Event Web Management 117 Web Management 118 Vlan Port Management Ports Web Management 120 Trunking Port Management Trunking Group Name Web Management 122 Web Management 123 Web Management 124 Troubleshooting Troubleshooting 126 LED Error Chart Explanation of LED Error Status Modular Status Error LED Indicator Chart Switch Specifications Appendix a DES-5200 Technical Specifications Port Specifications Appendix a 132 EMI Appendix a 134 Index 45, 92 Xmodem