Port 100BASE-FX Module | D-Link DES-5200 manual

Fast Ethernet Switching System User’s Guide

2-Port 100BASE-FX Module

Link

Transmitting

Receiving

Collision

Figure 17: 2-Port 100BASE-FX Module

The LEDs on the 2-Port 100BASE-FX Module, displayed in Figure 17, are different from the LEDs on the modules. The information given is the same but it is presented differently. Refer to Table 10: FX Module LED.

Lk

Lk indicates there is a link. The Lk LED lights to indicate there is a link at the port.

Dx

Dx means duplex mode. The Dx LED indicates the port’s duplex mode. The ports will not auto negotiate the duplex mode. The default value is half duplex. They can be manually set for full duplex. The LED is lit when the port is in full duplex and dark when the port is in half duplex.

Tx

Tx means transmitting. The Tx LED lights to indicate the port is transmitting data.

Rx

Rx means receiving. The Rx LED flashes when the port is receiving data.

Col

Col means collision. The Col LED lights amber when collisions occur at the port. Collisions are normal on the network. You should only be concerned when a high number of collisions happen at the port.

LEDs

33

Image 40

D-Link DES-5200 manual Port 100BASE-FX Module

Contents

DES-5200 Fast Ethernet Switching System User’s Guide Limited Warranty Link Offices for Registration and Warranty ServiceHardware Software Europe and Israel Wichtige Sicherheitshinweise Table of Contents Web Management 125 Audience Organization Features Introduction Fast Ethernet Switching System User’s Guide Front Panel Models Full Size Modules Optional Modules DES-5224TX DES-5220TF DES-5216FX.A1 DES-5216FX Rear Panel DES-5200 Rear Panel Software Update Management Methods Installing the DES-5200 Unpacking the DES-5200 Installation Options Desktop/ Shelf Installation Install Feet on Bottom Attach Feet Rack Installation Attach Mounting Brackets Insert into Rack Installing Optional Modules Remove Blank Bracket Insert Optional Module Power On Cable Specifications Copper Cable 10BASE-T Cable Diagram Fiber Optic Cable Ports MDI-X PortsFiber Optic Ports RS-232 Port Connecting the DES-5200 to other Switches and Hubs DES-5200 to DES-5200 Connection LEDs Power DiagnosticCPU Module Status LED Link Port 10/100-TX ModuleDuplex 100/10 FDX Col Link/Act Port FX ModuleFull/Half Port 100BASE-FX Module Port 100BASE-FX Module FX Module LED Port 1000BASE-SX Module Act Console Based Management Console Management ∙ Parity None ∙ Stop bits ∙ Flow Control Xon/Xoff Configuring Through the Ethernet Port Telnet Management ∙ Default User Name D-Link ∙ Default Password D-Link Log Help Message Help Message Panel Conventions Spacebar System Configuration Switch Port ConfigurationSpanning Tree Configuration Console Program Snmp Management Configuration Vlan Port ManagementTrunking Port Management Port Statistics System Configuration Menu System ResetFactory Reset to Default Config Values System Information Software Update Boot Prom Firmware VersionSystem Information Menu Hardware Revision LAN Default Gateway MAC AddressSystem Description System Name System Reset Factory Reset Factory Reset Advantages of Store and Forward Disadvantages of Store and Forward Advantages of Cut-Through Disadvantages of Cut-Through Software Update Menu Software Update Configuration Software Update Confirmation Send File Xmodem Tftp Tftp Transfer Complete User Account Management User Account Change Menu Password Confirm PasswordAccess Level Create New User Fast Ethernet Switching System User’s Guide Delete Users Delete Fast Ethernet Switching System User’s Guide Old Password Change PasswordNew Password Select Save and press Enter to save your changes Switch Port Configuration State Switch Port Configuration MenuPhysical Port State Priority Spanning Tree Configuration Spanning Tree Configuration MenuSTA Operation Levels Spanning Tree Algorithm Forward Delay Time Bridge PriorityRoot Cost Hello Time Root Bridge Root Port Snmp Management Configuration Snmp Management Configuration Menu Snmp Manager SettingAccess Right Snmp Community String Snmp Trap Manager Setting Authentication FailureCold Start Link Change Event Status Vlan Port Management Vlan Port Management Menu Vlan Port Management menu Create New Vlan New Vlan NamePort # TrunkGroup Fast Ethernet Switching System User’s Guide Delete Vlan Menu Vlan Name Modify Vlan Menu Virtual LAN Name Trunking Port Management Menu Trunking Port Management menu New Trunking Group Name Create New Trunking PortName Fast Ethernet Switching System User’s Guide Delete Trunking Port Trunking Port Modify Trunking Port Trunking Port Name Port Statistics TX FCS Errors Tx Run ErrorsRx Align or FCS Errors Rx Error Oversized Rx Error Undersized Rx Good UndersizedRx64 Rx65 to Using Web Management CommandsApply Refresh Logging User Name and Password System Configuration System Information Boot Prom Firmware Version System Information MenuHardware Revision Software Version LAN Default Gateway MAC AddressSystem Description System Name System Reset Factory Reset Factory Reset Confirmation System Rate Control Disadvantages of Store and Forward Software Update Web Management 101 Software Download Download Successful Web Management 104 Change Password Web Management 106 Switch Port Configuration Confirmation Web Management 108 Spanning Tree Configuration Web Management 110 Web Management 111 Web Management 112 Web Management 113 Snmp Manager Setting Snmp Trap Manager Setting Snmp Trap Manager Setting ∙ Cold Start ∙ Authentication Failure ∙ Link Change Event Web Management 117 Web Management 118 Ports Vlan Port Management Web Management 120 Trunking Group Name Trunking Port Management Web Management 122 Web Management 123 Web Management 124 Troubleshooting Troubleshooting 126 LED Error Chart Explanation of LED Error Status Modular Status Error LED Indicator Chart Appendix a DES-5200 Technical Specifications Switch Specifications Port Specifications Appendix a 132 EMI Appendix a 134 Index 45, 92 Xmodem