Manuals / D-Link / Computer Equipment / Network Router

D-Link DI-308 manual Static ARP

Models: DI-308

1 131

Download 131 pages 18.9 Kb

Page 63

Static ARP

DI-308 ISDN Remote Router

The parameters are described below:

•IP Address – This is a network IP address of a separate IP network on the LAN.

•Routing Protocol – This is the same as in the Network Configuration section. Keep in mind that these exchanges are made with adjacent routers on the LAN, if present.

•IP Multicasting – This enables or disables IP multicasting on the IP network you are defining.

All other parameters (Netmask, Routing Mode, Multicast Protocol and IGMP Version) are identical to those in the Network Configuration, IP Stack Configuration, ISDN screens.

Static ARP

This special function is intended to speed up the process of finding a host's Ethernet (MAC) address from its network address, and provides a special condition – any other host acting as an impostor by using the same IP address as the legitimate host, will be ignored by this router.

Basically, when a packet comes into the router from the ISDN line and is destined for a host on the LAN, the router will use information defined here to immediately send the packet to the host rather than send out an ARP request to find the host’s MAC address.

55

Image 63

D-Link DI-308 manual Static ARP

Contents

Rev. 02 August DI-308 ISDN Router User’s GuideTrademarks FCC WarningCE Mark Warning Copyright StatementSoftware Limited WarrantyD-Link Offices for Registration and Warranty Service HardwareWichtige Sicherheitshinweise INTRODUCTION Table of ContentsINSTALLATION CONFIGURATION AND MANAGEMENTAPPENDIX A - TROUBLESHOOTING PROM SYSTEM CONFIGURATIONUSING TELNET USING RADIUS AUTHENTICATIONAPPENDIX E - COUNTRY ID NUMBERS APPENDIX D - TECHNICAL SPECIFICATIONSAPPENDIX F - CONFIGURATION FILE APPENDIX C - IP PROTOCOL AND PORT NUMBERSPage Introduction Product FeaturesEase of Installation Built-in SwitchStandard Phone Jacks RADIUS Remote Authentication Dial in User ServiceDHCP Support Dynamic Host Configuration Protocol ISDN Leased LineData Compression Internet AccessApplications for your DI-308 What This Manual CoversWhat This Manual Doesn’t Cover This User’s Guide Additional Installation RequirementsOther Resources Packing ListInstallation The DI-308 Front PanelOrdering Your ISDN Line The DI-308 Rear Panel Installation and Initial Configuration Telephone FeaturesStep 1 - Setting up the Console Step 2 - Connecting the Console to the RouterA Warning on Connection Cables Step 5 - Connecting Ethernet Cables to the Router Using the ConsoleStep 3 - Connecting an ISDN Line to the Router Step 4 - Connecting a Telephone or Fax Machine to the RouterImportant Notes on Ethernet Connections Step 7 - Initial Configuration of the Router Step 6 - Powering Up Devices for Initial ConfigurationTo log on to the router, use the factory set username and password ‘Admin’ without the quotes. Please note that the user name and password are case-sensitive From the Main Menu choose Advanced Functions Step 8 - Configuring the LAN PortChoose Interface Configuration, LAN Choose Network Configuration, IP ConfigurationStep 9 - Plugging in All Devices Console Program Main Menu Configuration and ManagementThe above parameters are described as follows System InformationThis menu contains administrative and system-related information The Main Menu is shown belowInterface Configuration Operation Mode - The LAN port is Auto Negotiation only State - This is a toggle to Enable or Disable the LAN interfaceThe parameters are described below ISDN Network Configuration IP Stack Configuration IP ConfigurationDI-308 ISDN Remote Router Below, the submenus for both the LAN and ISDN interfaces are shownThe parameters are described below change to an adjacent router. The adjacent router must be using the same protocol. Setting this to RIPV1&V2 will give the router the ability to make routing information exchanges with any adjacent router IP Static Route SNMP Agent Configuration IP NetworkingRouter Advertisement SNMP Community Configuration SNMP Trap Manager Advanced Functions SNMP Authenticated TrapRemote Access Configuration Dial-In Network Connections Remote Operation OverviewDial-In User Connections Remote Network ConnectionsWhen a packet on the LAN reaches the router, the DI-308 will DI-308 ISDN Remote Router Dial In IP Pool Dial ConfigurationThe items are described as follows Dial-In User Profile DI-308 ISDN Remote Router Press Enter to access the submenu that appears belowPassword - This is the password associated with the above Name field The parameters in the above window are described as followsRemote Network Profile Phone Number Supplied by - Toggle between Router and CallerPress Enter to access the submenu that appears below Incoming Outgoing DHCP ConfigurationDHCP Server Configuration Dynamic IP Pool Static IP Pool DHCP Relay Agent Configuring a Filter Set Filter ConfigurationFilter State of Interface Layer 2 Filter Press Enter to access the following screen The parameters of a filter are described belowDI-308 ISDN Remote Router IP Filter Press Enter to access the following screen The IP Filter parameters are described belowDI-308 ISDN Remote Router 3. Disable - This does not apply the IP filter Multiple Home Configuration Static ARP DI-308 ISDN Remote Router Press Enter to access the following screenState - This toggles enable or disable The parameters are described as followsHow NAT Works NAT ConfigurationRouter NAT Page Beginning Address Setting Local IP AddressesNAT/NAPT ClassThe configuration screen for the name field appears as follows NAT IP Pool Configuration Screen Dynamic NATDynamic NAPT Static NAT Static NAPT Configure NAPT for Special Applications The fields in the above window are described as follows Start Port - Some applications can only send data over a certain range of port numbers. Thus, all port numbers in the specified range must be exempt from the NAPT port translation process. This field defines the beginning range of the port numbers to be exempted from the NAPT port translation process DNS Configuration Telnet/Discovery EnableHost Table DI-308 ISDN Remote Router State - Enables or disables entryItems are described as follows IP - The IP address for the host Host Name - The host name used by the hostRADIUS Configuration Multi-Link PPP Configuration Bandwidth on Demand - Enables or disables BOD. When enabled, BOD will manage the implementation of MLPPP using the parameters defined in this window System Maintenance Admin ConfigurationStatistics System StatusLAN Counter Table Tx Bytes - The total number of bytes transmitted by the routerTx Discard Packets - The number of packets dropped by the router Rx Packets - The number of valid packets received by the router ISDN Counter Table IP Routing Table Runtime TablesHops - This is the remaining hop-count PPP Table ARP TableLog and Trace Event/Error Log Log ConfigurationView Log File Trace Buffer Direction - The incoming or outgoing connection direction Trace Buffer ConfigurationEnables or disables the Trace Buffer feature The contents are described as followsPacket Triggered Last Call View Trace BufferDiagnostic Connection TestThis feature tests a dial-out ISDN connection IP Ping Test Loopback Test Press Enter to access the next screen Start Test - press Enter or Return to begin the testDI-308 ISDN Remote Router System ISDN Test System LAN TestSystem Restart Software UpdateFactory Reset System Settings Backup/Restore Items in the windows above and below include DI-308 ISDN Remote Router PROM System Configuration System Configuration The parameters are described as followsMAC Address - This is the physical address for this router System Reset TCP/IP Parameters ConfigurationSoftware Update A system reset will not affect the router’s settings, but will clear all tables including the routing table and all SNMP counters and tables. It is also used to initiate a software updateSoftware Update Control - This toggles Disable and Enable EEPROM Factory Reset Execute BootloadDI-308 ISDN Remote Router Using Telnet via ISDN Using TelnetTelnet Configuration Using Telnet via LANSystem Timeout Using RADIUS Authentication Installing a RADIUS ServerConfiguring the DI-308 for RADIUS Authentication 192.168.0.1 Adding Users to the RADIUS DatabaseIp user Password = “iusespecificip”, FramedIPAddress = # Client NameProblems with the LAN Interface Appendix A - TroubleshootingSome Common Problems with the DI-308 Problems With the ISDN Line3. Verify with your network administrator that the IP address and the IP subnet mask configured in the Network Configuration, IP Configuration, IP Stack Configuration, LAN submenu of the console program are valid for that LAN Class Appendix B - IP ConceptsIP Addresses IP Network ClassesEnding Address Subnet MaskClass Beginning AddressAppendix C - IP Protocol and Port Numbers IP Protocol NumbersIP Port Numbers Appendix D - Technical Specifications GeneralPhysical & Environmental Ventilation South Africa Appendix E - Country ID NumbersConfiguration File Example Appendix F - Configuration FileDI-308 ISDN Remote Router Forward DNS queries to, 76, 77 Forwarding LAN IndexIP STACK Dynamic NAPT Static NAPTDynamic NAT Static NAT UNNUMBER TalkOffices Product was purchased from Registration CardProduct installed in type of computer e.g., Compaq Product installed in computer serial No