DSL-564T DSL Router User’s Guide

Information you will need from your ADSL service provider:

 

This is the Username used to log on to your ADSL service

Record info here

Username

provider’s network. It is commonly in the form

 

user@isp.com. Your ADSL service provider uses this to

 

 

 

 

identify your account.

 

 

 

 

 

This is the Password used, in conjunction with the Username

 

Password

above, to log on to your ADSL service provider’s network.

 

 

This is used to verify the identity of your account.

 

 

 

 

 

This is the method your ADSL service provider uses to send

 

 

and receive data between the Internet and your computer.

 

Connection Protocol

Your Modem supports the following connection protocols:

 

 

PPPoE, PPPoA, PPPoA with DHCP, Bridge, and CLIP

 

 

(IPoA).

 

 

 

 

 

ADSL uses various standardized modulation techniques to

 

 

transmit data over the allotted signal frequencies. Some

 

 

users may need to change the type of modulation used for

 

Modulation Type

their service. The default DSL modulation (MMODE) used for

 

the Router automatically detects all types of ADSL

 

 

 

 

modulation. However, if you are instructed to specify the

 

 

modulation type used for the Router, you have three

 

 

alternatives: G.LITE, G.DMT and T1.413

 

 

 

 

 

This is the method your ADSL service provider will use to

 

Security Protocol

verify your Username and Password when you log on to their

 

network. Your Modem supports the PAP and CHAP

 

 

 

 

protocols.

 

 

 

 

 

This is the Virtual Path Identifier (VPI). It is used in

 

VPI

conjunction with the Virtual Channel Identifier (VCI) below, to

 

identify the data path between your ADSL service provider’s

 

 

 

 

network and your computer.

 

 

 

 

 

This is the Virtual Channel Identifier (VCI). It is used in

 

VCI

conjunction with the VPI above to identify the data path

 

between your ADSL service provider’s network and your

 

 

 

 

computer.

 

 

 

 

Information you will need about your DSL-564T ADSL Router:

 

This is the Username needed access the Modem’s

Record info here

 

management interface. When you attempt to connect to the

 

Username

device through a web browser you will be prompted to enter

 

 

this Username. The default Username for the Modem is

 

 

admin. This may be changed by the user.

 

 

 

 

 

This is the Password you will be prompted to enter when you

 

Password

access the Modem’s management interface. The default

 

 

Password is admin. This may be changed by the user.

 

 

 

 

 

This is the IP address you will enter into the Address field of

 

 

your web browser to access the Modem’s configuration

 

 

graphical user interface (GUI) using a web browser. The

 

LAN IP addresses for the

default IP address is 192.168.1.1 and it is referred to as the

 

DSL-564T

“Management IP” address in this User’s Manual. This may be

 

 

changed to suit any IP address scheme the user desires. This

 

 

address will be the base IP address used for DHCP service

 

 

on the LAN when DHCP is enabled.

 

 

 

 

LAN Subnet Mask for the

This is the subnet mask used by the DSL-564T, and will be

 

used throughout your LAN. The default subnet mask is

 

DSL-564T

 

255.0.0.0. This can be changed later.

 

 

 

 

 

 

xi

Page 11
Image 11
D-Link DSL-564T manual Information you will need from your Adsl service provider