User’s / Programming Guide | Datalogic Scanning DS2200 SH2348

Transmission of the last character in a UPC symbol (the check digit) is disabled by scanning Option QF, or is enabled by scanning Option QG.

QF

QG

Disable Transmission of Check Digit

Enable Transmission of Check Digit *#

Scanning QJ causes UPC-A labels to be transmitted as EAN-13 labels. Scanning QK disables this feature.

QJ

Enable UPC to EAN Translation

QK

QN

QO

QP

QR

Disable UPC to EAN Translation *#@

Disable second beep on

Supplement decoded *

Enable second beep on

Supplement decoded

Set supplement retry count (16 by default) range = 1-32

Disable transmissionof UPC-E check digit

40	User’s / Programming Guide

Image 48

Datalogic Scanning DS2200 SH2348, DS1100 SH2347 manual User’s / Programming Guide

Contents

User’s / Programming Guide PSC Inc DisclaimerPage Page Table of Contents Serial Commands Keyboard Wedge Parameters SymbologiesMessage Formatting Wand Emulation Parameters Iii Memory ModuleScanner Labeling Technical Support User’s / Programming Guide Introduction Installation Cable InstallationUnpacking Keyboard Wedge Connecting the Power Supply Connecting a Magnetic Stripe ReaderTerminal Power-Up Sequence Scanning Reset to Default ZA will cause the PSC scan Serial TTL Mode Serial RS232 ModeSerial Communications AutoSense Operation Enable AutoSense Disable AutoSense Scanner holder Stand base Enable Wedge Enable Serial Mode Wand Emulation OperationSame Code Wand Emulation Code Type = Same Code Wand Emulation Setup Overview Wedge Mode OptionsWand Emulation Options Serial Communication and Wedge Options Data SynchronizationBaud Rate Protocol Parity Stop Bits Symbologies Code Interleaved 2 Standard 2 CodabarCode Vice representative Beeper On Volume Low Parameters Selection GuidelinesExamples User’s / Programming Guide Reset Default Serial CommunicationBaud Rate Select Serial Output Data Transmission Bit Options Data Stop Bits ParityOdd Even Mark Space Mark Space Bit, No Parity Communications ProtocolNone Inverted Serial Communications CTS Disable Stop/Go Protocol Enable Stop/Go Protocol Enable No Read Disable No Read Label BufferingNo Read Option Full Buffering No Buffering One Label Buffering Menu Commands Parameter Messages Enable Parameter Messages Disable Parameter MessagesDisable External Trigger#*@ External Trigger+ External Trigger Operation Intercharacter Delay No interlabel delay *@ Set interlabel delay 0-9.9 secondsGeneral Parameters External Trigger Transmission Mode System Status Power Consumption Display ConfigurationEnable Continuous@ Full Power Enable Standby *# Laser Redundancy Laser Timeout Enable 4 Times Laser RedundancyBeeper Off Beeper On Volume Low Beeper Operation Beeper On Volume Medium Beeper On Volume Loud *#@ Message FormattingPrefixes and Suffixes Programmable options do not apply in Wand Emu Lation Prefix SuffixPrefix = None*# Prefix = STX Prefix = SOH Suffix = CR and LF Terminal ID Select Suffix = ETB NUL Code Identifier Code Identifier Characters Preamble or Postamble Selection PreamblePostamble 0,0 hexadecimal User’s / Programming Guide Serial Commands General Serial Command Format Command Function Enable I 2 of 5 with check digitBeeper Off CR-LF Ack Power Standby and Serial Commands Communication Parameter ChangesManual Scanning Interaction Wedge Mode Enable @ Keyboard Wedge Parameters 06656 User’s / Programming Guide Explained in Appendix a Symbologies Disable UPC both a and EUPC a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Enable transmissionof UPC-E check digit Disable UPC-E Disable EAN/JAN 8 or 13 Digit #@ EAN/JAN Disable EAN-8 independently Disable Code Code Following are only valid if CHK Char is enabled Do Not Xmit Start and STOP*#@ Transmit Start and Stop Disable Interleaved Code 2 of 5*#@ Code 2 of 5 InterleavedMaximum Length I 2 of 5 specified by two digits Code 2 of 5 Standard Enable Code 128 *#@ Disable Codabar *#@Enable Codabar Minimum Length specified by two digits Enable Transmission of START/ Stop Character Maximum Length specified by two digits MSI/Plessey Enable Code Standard Code Enable 16K Code Disable 16K Code 16K Digit Selection Symbology Identifiers Symbol Function 06656 Programming Symbol Bology identifiers Symbology Identifiers EAN-13 CodeStandard 2/5 Code MSI/Plessey Wand Emulation Parameters Select Code TypeBar Code Polarity Transmission Rate Inches per second# Disable Data # Synchronization Enable Data Synchronization Data Synchronization Active # Polarity High Active Polarity Low Memory Module Setup Disable Memory Module*# Enable Memory Module Enable Marker Beam Disable Marker Beam Marker Beam 06656 Service and Warranty Scanner LabelingHazardous visible light exposure Maintenance CleaningInspection Technical Support PSC Website Support PSC Website TekForumReseller Technical Support Telephone Technical Support Appendix a Hexadecimal Conversion Table Part a Part B Primary Function Key Table Ascii HEX Function Secondary Function Key Tables PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25 IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc