User’s / Programming Guide | Datalogic Scanning DS2200 SH2348

NOTES

78	User’s / Programming Guide

Image 86

Datalogic Scanning DS2200 SH2348, DS1100 SH2347 manual User’s / Programming Guide

Contents

User’s / Programming Guide PSC Inc DisclaimerPage Page Table of Contents Message Formatting Serial CommandsKeyboard Wedge Parameters Symbologies Wand Emulation Parameters Scanner Labeling IiiMemory Module Technical Support User’s / Programming Guide Introduction Unpacking InstallationCable Installation Keyboard Wedge Terminal Power-Up Sequence Connecting the Power SupplyConnecting a Magnetic Stripe Reader Scanning Reset to Default ZA will cause the PSC scan Serial Communications Serial TTL ModeSerial RS232 Mode AutoSense Operation Enable AutoSense Disable AutoSense Scanner holder Stand base Same Code Wand Emulation Enable Wedge Enable Serial ModeWand Emulation Operation Code Type = Same Code Wand Emulation Wand Emulation Options Setup OverviewWedge Mode Options Baud Rate Protocol Parity Serial Communication and Wedge OptionsData Synchronization Stop Bits Code SymbologiesCode Interleaved 2 Standard 2 Codabar Vice representative Examples Beeper On Volume LowParameters Selection Guidelines User’s / Programming Guide Baud Rate Reset DefaultSerial Communication Select Serial Output Odd Even Mark Space Data TransmissionBit Options Data Stop Bits Parity Mark Space None Bit, No ParityCommunications Protocol Inverted Serial Communications CTS Disable Stop/Go Protocol Enable Stop/Go Protocol No Read Option Enable No Read Disable No ReadLabel Buffering Full Buffering No Buffering One Label Buffering Disable External Trigger#*@ External Trigger+ Menu Commands Parameter MessagesEnable Parameter Messages Disable Parameter Messages External Trigger Operation General Parameters Intercharacter DelayNo interlabel delay *@ Set interlabel delay 0-9.9 seconds External Trigger Transmission Mode System Status Enable Continuous@ Full Power Enable Standby *# Power ConsumptionDisplay Configuration Laser Redundancy Beeper Off Beeper On Volume Low Laser TimeoutEnable 4 Times Laser Redundancy Beeper Operation Prefixes and Suffixes Beeper On Volume Medium Beeper On Volume Loud *#@Message Formatting Programmable options do not apply in Wand Emu Lation Prefix = None*# Prefix = STX Prefix = SOH PrefixSuffix Suffix = CR and LF Terminal ID Select Suffix = ETB NUL Code Identifier Code Identifier Characters Postamble Preamble or Postamble SelectionPreamble 0,0 hexadecimal User’s / Programming Guide Serial Commands General Serial Command Format Beeper Off CR-LF Ack Command FunctionEnable I 2 of 5 with check digit Manual Scanning Interaction Power Standby and Serial CommandsCommunication Parameter Changes Wedge Mode Enable @ Keyboard Wedge Parameters 06656 User’s / Programming Guide Explained in Appendix a UPC a and E SymbologiesDisable UPC both a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Enable transmissionof UPC-E check digit Disable UPC-E Disable EAN/JAN 8 or 13 Digit #@ EAN/JAN Disable EAN-8 independently Disable Code Code Following are only valid if CHK Char is enabled Do Not Xmit Start and STOP*#@ Transmit Start and Stop Maximum Length I 2 of 5 specified by two digits Disable Interleaved Code 2 of 5*#@Code 2 of 5 Interleaved Code 2 of 5 Standard Enable Codabar Enable Code 128 *#@Disable Codabar *#@ Minimum Length specified by two digits Enable Transmission of START/ Stop Character Maximum Length specified by two digits MSI/Plessey Enable Code Standard Code Enable 16K Code Disable 16K Code 16K Digit Selection Symbology Identifiers Symbol Function 06656 Programming Symbol Bology identifiers Standard 2/5 Code Symbology IdentifiersEAN-13 Code MSI/Plessey Bar Code Polarity Wand Emulation ParametersSelect Code Type Transmission Rate Inches per second# Disable Data # Synchronization Enable Data Synchronization Data Synchronization Active # Polarity High Active Polarity Low Memory Module Setup Disable Memory Module*# Enable Memory Module Enable Marker Beam Disable Marker Beam Marker Beam 06656 Hazardous visible light exposure Service and WarrantyScanner Labeling Inspection MaintenanceCleaning Reseller Technical Support Technical SupportPSC Website Support PSC Website TekForum Telephone Technical Support Appendix a Hexadecimal Conversion Table Part a Part B Primary Function Key Table Ascii HEX Function Secondary Function Key Tables PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25 IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc