Enable Code 128 *#@ | Datalogic Scanning DS2200 SH2348 instruction

Code 128

Scan Option TA to disable Code 128.

TA

Disable Code 128

Scan Option TB to enable Code 128.

TB

Enable Code 128 *#@

The minimum length of Code 128 messages is set by scanning Option TC, followed by scanning two digits (01-32) from the Digit Selection page.

TC

Minimum Length (specified by two digits 01-32)

The maximum length of Code 128 messages is set by scanning Option TD, followed by scanning two digits (01-32) from the Digit Selection page. If the minimum and maximum values are set equal, only codes of that exact length are read.

TD

Maximum Length (specified by two digits 01-32) Codabar

Scan Option VA to disable Codabar.

VA

Disable Codabar *#@

Scan Option VB to enable Codabar.

VB

Enable Codabar

48	User’s / Programming Guide

Image 56

Datalogic Scanning DS2200 SH2348 manual Enable Code 128 *#@, Minimum Length specified by two digits, Disable Codabar *#@

Contents

User’s / Programming Guide PSC Inc DisclaimerPage Page Table of Contents Serial Commands Keyboard Wedge Parameters SymbologiesMessage Formatting Wand Emulation Parameters Iii Memory ModuleScanner Labeling Technical Support User’s / Programming Guide Introduction Installation Cable InstallationUnpacking Keyboard Wedge Connecting the Power Supply Connecting a Magnetic Stripe ReaderTerminal Power-Up Sequence Scanning Reset to Default ZA will cause the PSC scan Serial Communications Serial TTL ModeSerial RS232 Mode AutoSense Operation Enable AutoSense Disable AutoSense Scanner holder Stand base Enable Wedge Enable Serial Mode Wand Emulation OperationSame Code Wand Emulation Code Type = Same Code Wand Emulation Wand Emulation Options Setup OverviewWedge Mode Options Serial Communication and Wedge Options Data SynchronizationBaud Rate Protocol Parity Stop Bits Symbologies Code Interleaved 2 Standard 2 CodabarCode Vice representative Examples Beeper On Volume LowParameters Selection Guidelines User’s / Programming Guide Reset Default Serial CommunicationBaud Rate Select Serial Output Odd Even Mark Space Data TransmissionBit Options Data Stop Bits Parity Mark Space Bit, No Parity Communications ProtocolNone Inverted Serial Communications CTS Disable Stop/Go Protocol Enable Stop/Go Protocol Enable No Read Disable No Read Label BufferingNo Read Option Full Buffering No Buffering One Label Buffering Menu Commands Parameter Messages Enable Parameter Messages Disable Parameter MessagesDisable External Trigger#*@ External Trigger+ External Trigger Operation Intercharacter Delay No interlabel delay *@ Set interlabel delay 0-9.9 secondsGeneral Parameters External Trigger Transmission Mode System Status Power Consumption Display ConfigurationEnable Continuous@ Full Power Enable Standby *# Laser Redundancy Laser Timeout Enable 4 Times Laser RedundancyBeeper Off Beeper On Volume Low Beeper Operation Beeper On Volume Medium Beeper On Volume Loud *#@ Message FormattingPrefixes and Suffixes Programmable options do not apply in Wand Emu Lation Prefix = None*# Prefix = STX Prefix = SOH PrefixSuffix Suffix = CR and LF Terminal ID Select Suffix = ETB NUL Code Identifier Code Identifier Characters Preamble or Postamble Selection PreamblePostamble 0,0 hexadecimal User’s / Programming Guide Serial Commands General Serial Command Format Beeper Off CR-LF Ack Command FunctionEnable I 2 of 5 with check digit Manual Scanning Interaction Power Standby and Serial CommandsCommunication Parameter Changes Wedge Mode Enable @ Keyboard Wedge Parameters 06656 User’s / Programming Guide Explained in Appendix a UPC a and E SymbologiesDisable UPC both a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Enable transmissionof UPC-E check digit Disable UPC-E Disable EAN/JAN 8 or 13 Digit #@ EAN/JAN Disable EAN-8 independently Disable Code Code Following are only valid if CHK Char is enabled Do Not Xmit Start and STOP*#@ Transmit Start and Stop Maximum Length I 2 of 5 specified by two digits Disable Interleaved Code 2 of 5*#@Code 2 of 5 Interleaved Code 2 of 5 Standard Enable Code 128 *#@ Disable Codabar *#@Enable Codabar Minimum Length specified by two digits Enable Transmission of START/ Stop Character Maximum Length specified by two digits MSI/Plessey Enable Code Standard Code Enable 16K Code Disable 16K Code 16K Digit Selection Symbology Identifiers Symbol Function 06656 Programming Symbol Bology identifiers Symbology Identifiers EAN-13 CodeStandard 2/5 Code MSI/Plessey Wand Emulation Parameters Select Code TypeBar Code Polarity Transmission Rate Inches per second# Disable Data # Synchronization Enable Data Synchronization Data Synchronization Active # Polarity High Active Polarity Low Memory Module Setup Disable Memory Module*# Enable Memory Module Enable Marker Beam Disable Marker Beam Marker Beam 06656 Hazardous visible light exposure Service and WarrantyScanner Labeling Inspection MaintenanceCleaning Technical Support PSC Website Support PSC Website TekForumReseller Technical Support Telephone Technical Support Appendix a Hexadecimal Conversion Table Part a Part B Primary Function Key Table Ascii HEX Function Secondary Function Key Tables PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25 IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc