Datalogic Scanning DS1100 SH2347, DS2200 SH2348 specs

The minimum length of Code 39 messages is set by scanning Option OH, followed by scanning two digits (01-32) from the Digit Selection page.

OH

Minimum Length (specified by two digits 01-32)

The maximum length of Code 39 messages is set by scanning Option OI, followed by scanning two digits (01-32) from the Digit Selection page. If the minimum and maximum values are set equal, only codes of that exact length are read.

OI

Maximum Length (specified by two digits 01-32)

The START and STOP characters in code 39 may either be transmitted or suppressed. Scan Option OF to suppress transmission of the START and STOP characters. Scan Option OG to enable transmission.

OF

Do Not XMIT START and STOP*#@

OG

Transmit START and STOP

The following are only valid if CHK CHAR is enabled.

OJ

OK

Enable Transmission of Code 39 Modulo 43 Check Character

Disable Transmission of Code 39 Modulo 43 Check Character *

06656

45

Image 53

Datalogic Scanning DS1100 SH2347, DS2200 SH2348 manual Do Not Xmit Start and STOP*#@ Transmit Start and Stop

Contents

User’s / Programming Guide Disclaimer PSC IncPage Page Table of Contents Keyboard Wedge Parameters Symbologies Serial CommandsMessage Formatting Wand Emulation Parameters Memory Module IiiScanner Labeling Technical Support User’s / Programming Guide Introduction Cable Installation InstallationUnpacking Keyboard Wedge Connecting a Magnetic Stripe Reader Connecting the Power SupplyTerminal Power-Up Sequence Scanning Reset to Default ZA will cause the PSC scan Serial Communications Serial TTL ModeSerial RS232 Mode AutoSense Operation Scanner holder Stand base Enable AutoSense Disable AutoSense Wand Emulation Operation Enable Wedge Enable Serial ModeSame Code Wand Emulation Code Type = Same Code Wand Emulation Wand Emulation Options Setup OverviewWedge Mode Options Data Synchronization Serial Communication and Wedge OptionsBaud Rate Protocol Parity Stop Bits Code Interleaved 2 Standard 2 Codabar SymbologiesCode Vice representative Examples Beeper On Volume LowParameters Selection Guidelines User’s / Programming Guide Serial Communication Reset DefaultBaud Rate Select Serial Output Odd Even Mark Space Data TransmissionBit Options Data Stop Bits Parity Mark Space Communications Protocol Bit, No ParityNone Inverted Serial Communications CTS Disable Stop/Go Protocol Enable Stop/Go Protocol Label Buffering Enable No Read Disable No ReadNo Read Option Full Buffering No Buffering One Label Buffering Enable Parameter Messages Disable Parameter Messages Menu Commands Parameter MessagesDisable External Trigger#*@ External Trigger+ External Trigger Operation No interlabel delay *@ Set interlabel delay 0-9.9 seconds Intercharacter DelayGeneral Parameters External Trigger System Status Transmission Mode Display Configuration Power ConsumptionEnable Continuous@ Full Power Enable Standby *# Laser Redundancy Enable 4 Times Laser Redundancy Laser TimeoutBeeper Off Beeper On Volume Low Beeper Operation Message Formatting Beeper On Volume Medium Beeper On Volume Loud *#@Prefixes and Suffixes Programmable options do not apply in Wand Emu Lation Prefix = None*# Prefix = STX Prefix = SOH PrefixSuffix Terminal ID Select Suffix = ETB NUL Suffix = CR and LF Code Identifier Characters Code Identifier Preamble Preamble or Postamble SelectionPostamble 0,0 hexadecimal User’s / Programming Guide General Serial Command Format Serial Commands Beeper Off CR-LF Ack Command FunctionEnable I 2 of 5 with check digit Manual Scanning Interaction Power Standby and Serial CommandsCommunication Parameter Changes Keyboard Wedge Parameters Wedge Mode Enable @ 06656 User’s / Programming Guide Explained in Appendix a UPC a and E SymbologiesDisable UPC both a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Disable UPC-E Enable transmissionof UPC-E check digit EAN/JAN Disable EAN/JAN 8 or 13 Digit #@ Disable EAN-8 independently Code Disable Code Do Not Xmit Start and STOP*#@ Transmit Start and Stop Following are only valid if CHK Char is enabled Maximum Length I 2 of 5 specified by two digits Disable Interleaved Code 2 of 5*#@Code 2 of 5 Interleaved Code 2 of 5 Standard Disable Codabar *#@ Enable Code 128 *#@Enable Codabar Minimum Length specified by two digits Maximum Length specified by two digits Enable Transmission of START/ Stop Character MSI/Plessey Enable Code Standard Code 16K Enable 16K Code Disable 16K Code Digit Selection Symbol Function Symbology Identifiers 06656 Bology identifiers Programming Symbol EAN-13 Code Symbology IdentifiersStandard 2/5 Code MSI/Plessey Select Code Type Wand Emulation ParametersBar Code Polarity Transmission Rate Inches per second# Data Synchronization Disable Data # Synchronization Enable Data Synchronization Active # Polarity High Active Polarity Low Memory Module Disable Memory Module*# Enable Memory Module Setup Marker Beam Enable Marker Beam Disable Marker Beam 06656 Hazardous visible light exposure Service and WarrantyScanner Labeling Inspection MaintenanceCleaning PSC Website Support PSC Website TekForum Technical SupportReseller Technical Support Telephone Technical Support Hexadecimal Conversion Table Appendix a Part a Part B Ascii HEX Function Primary Function Key Table PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25 Secondary Function Key Tables IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc