Disable EAN-8 independently | Datalogic Scanning DS1100 SH2347

Transmission of the last character in an EAN/JAN symbol (the check digit) is disabled by scanning Option RF, or is enabled by scanning Option RG.

RF

RG

RJ

RK

RL

RM

RN

RO

RP

Disable Transmission of Check Digit

Enable Transmission of Check Digit *#@

Disable EAN-8 Transmission of check character

Enable EAN-8 Transmission of check character*

Disable EAN-8 Transmission of number system digit

Enable EAN-8 Transmission of number system digit*

Disable EAN-8 independently*

Enable EAN-8 independently with supplement

Enable EAN-8 independently without supplement

06656

43

Image 51

Datalogic Scanning DS1100 SH2347, DS2200 SH2348 manual Disable EAN-8 independently

Contents

User’s / Programming Guide Disclaimer PSC IncPage Page Table of Contents Wand Emulation Parameters Serial CommandsKeyboard Wedge Parameters Symbologies Message Formatting Technical Support IiiMemory Module Scanner Labeling User’s / Programming Guide Introduction Keyboard Wedge InstallationCable Installation Unpacking Scanning Reset to Default ZA will cause the PSC scan Connecting the Power SupplyConnecting a Magnetic Stripe Reader Terminal Power-Up Sequence Serial TTL Mode Serial RS232 ModeSerial Communications AutoSense Operation Scanner holder Stand base Enable AutoSense Disable AutoSense Code Type = Same Code Wand Emulation Enable Wedge Enable Serial ModeWand Emulation Operation Same Code Wand Emulation Setup Overview Wedge Mode OptionsWand Emulation Options Stop Bits Serial Communication and Wedge OptionsData Synchronization Baud Rate Protocol Parity Vice representative SymbologiesCode Interleaved 2 Standard 2 Codabar Code Beeper On Volume Low Parameters Selection GuidelinesExamples User’s / Programming Guide Select Serial Output Reset DefaultSerial Communication Baud Rate Data Transmission Bit Options Data Stop Bits ParityOdd Even Mark Space Mark Space Inverted Serial Communications Bit, No ParityCommunications Protocol None CTS Disable Stop/Go Protocol Enable Stop/Go Protocol Full Buffering No Buffering One Label Buffering Enable No Read Disable No ReadLabel Buffering No Read Option External Trigger Operation Menu Commands Parameter MessagesEnable Parameter Messages Disable Parameter Messages Disable External Trigger#*@ External Trigger+ External Trigger Intercharacter DelayNo interlabel delay *@ Set interlabel delay 0-9.9 seconds General Parameters System Status Transmission Mode Laser Redundancy Power ConsumptionDisplay Configuration Enable Continuous@ Full Power Enable Standby *# Beeper Operation Laser TimeoutEnable 4 Times Laser Redundancy Beeper Off Beeper On Volume Low Programmable options do not apply in Wand Emu Lation Beeper On Volume Medium Beeper On Volume Loud *#@Message Formatting Prefixes and Suffixes Prefix SuffixPrefix = None*# Prefix = STX Prefix = SOH Terminal ID Select Suffix = ETB NUL Suffix = CR and LF Code Identifier Characters Code Identifier 0,0 hexadecimal Preamble or Postamble SelectionPreamble Postamble User’s / Programming Guide General Serial Command Format Serial Commands Command Function Enable I 2 of 5 with check digitBeeper Off CR-LF Ack Power Standby and Serial Commands Communication Parameter ChangesManual Scanning Interaction Keyboard Wedge Parameters Wedge Mode Enable @ 06656 User’s / Programming Guide Explained in Appendix a Symbologies Disable UPC both a and EUPC a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Disable UPC-E Enable transmissionof UPC-E check digit EAN/JAN Disable EAN/JAN 8 or 13 Digit #@ Disable EAN-8 independently Code Disable Code Do Not Xmit Start and STOP*#@ Transmit Start and Stop Following are only valid if CHK Char is enabled Disable Interleaved Code 2 of 5*#@ Code 2 of 5 InterleavedMaximum Length I 2 of 5 specified by two digits Code 2 of 5 Standard Minimum Length specified by two digits Enable Code 128 *#@Disable Codabar *#@ Enable Codabar Maximum Length specified by two digits Enable Transmission of START/ Stop Character MSI/Plessey Enable Code Standard Code 16K Enable 16K Code Disable 16K Code Digit Selection Symbol Function Symbology Identifiers 06656 Bology identifiers Programming Symbol MSI/Plessey Symbology IdentifiersEAN-13 Code Standard 2/5 Code Transmission Rate Wand Emulation ParametersSelect Code Type Bar Code Polarity Inches per second# Data Synchronization Disable Data # Synchronization Enable Data Synchronization Active # Polarity High Active Polarity Low Memory Module Disable Memory Module*# Enable Memory Module Setup Marker Beam Enable Marker Beam Disable Marker Beam 06656 Service and Warranty Scanner LabelingHazardous visible light exposure Maintenance CleaningInspection Telephone Technical Support Technical SupportPSC Website Support PSC Website TekForum Reseller Technical Support Hexadecimal Conversion Table Appendix a Part a Part B Ascii HEX Function Primary Function Key Table PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25 Secondary Function Key Tables IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc