06656 | Datalogic Scanning DS1100 SH2347, DS2200 SH2348 manual

NOTES

06656

77

Image 85

Datalogic Scanning DS1100 SH2347, DS2200 SH2348 manual 06656

Contents

User’s / Programming Guide Disclaimer PSC IncPage Page Table of Contents Keyboard Wedge Parameters Symbologies Serial CommandsMessage Formatting Wand Emulation Parameters Memory Module IiiScanner Labeling Technical Support User’s / Programming Guide Introduction Cable Installation InstallationUnpacking Keyboard Wedge Connecting a Magnetic Stripe Reader Connecting the Power SupplyTerminal Power-Up Sequence Scanning Reset to Default ZA will cause the PSC scan Serial RS232 Mode Serial TTL ModeSerial Communications AutoSense Operation Scanner holder Stand base Enable AutoSense Disable AutoSense Wand Emulation Operation Enable Wedge Enable Serial ModeSame Code Wand Emulation Code Type = Same Code Wand Emulation Wedge Mode Options Setup OverviewWand Emulation Options Data Synchronization Serial Communication and Wedge OptionsBaud Rate Protocol Parity Stop Bits Code Interleaved 2 Standard 2 Codabar SymbologiesCode Vice representative Parameters Selection Guidelines Beeper On Volume LowExamples User’s / Programming Guide Serial Communication Reset DefaultBaud Rate Select Serial Output Bit Options Data Stop Bits Parity Data TransmissionOdd Even Mark Space Mark Space Communications Protocol Bit, No ParityNone Inverted Serial Communications CTS Disable Stop/Go Protocol Enable Stop/Go Protocol Label Buffering Enable No Read Disable No ReadNo Read Option Full Buffering No Buffering One Label Buffering Enable Parameter Messages Disable Parameter Messages Menu Commands Parameter MessagesDisable External Trigger#*@ External Trigger+ External Trigger Operation No interlabel delay *@ Set interlabel delay 0-9.9 seconds Intercharacter DelayGeneral Parameters External Trigger System Status Transmission Mode Display Configuration Power ConsumptionEnable Continuous@ Full Power Enable Standby *# Laser Redundancy Enable 4 Times Laser Redundancy Laser TimeoutBeeper Off Beeper On Volume Low Beeper Operation Message Formatting Beeper On Volume Medium Beeper On Volume Loud *#@Prefixes and Suffixes Programmable options do not apply in Wand Emu Lation Suffix PrefixPrefix = None*# Prefix = STX Prefix = SOH Terminal ID Select Suffix = ETB NUL Suffix = CR and LF Code Identifier Characters Code Identifier Preamble Preamble or Postamble SelectionPostamble 0,0 hexadecimal User’s / Programming Guide General Serial Command Format Serial Commands Enable I 2 of 5 with check digit Command FunctionBeeper Off CR-LF Ack Communication Parameter Changes Power Standby and Serial CommandsManual Scanning Interaction Keyboard Wedge Parameters Wedge Mode Enable @ 06656 User’s / Programming Guide Explained in Appendix a Disable UPC both a and E SymbologiesUPC a and E Disable Expanded UPC-E *#@ Enable Expanded UPC-E User’s / Programming Guide Disable UPC-E Enable transmissionof UPC-E check digit EAN/JAN Disable EAN/JAN 8 or 13 Digit #@ Disable EAN-8 independently Code Disable Code Do Not Xmit Start and STOP*#@ Transmit Start and Stop Following are only valid if CHK Char is enabled Code 2 of 5 Interleaved Disable Interleaved Code 2 of 5*#@Maximum Length I 2 of 5 specified by two digits Code 2 of 5 Standard Disable Codabar *#@ Enable Code 128 *#@Enable Codabar Minimum Length specified by two digits Maximum Length specified by two digits Enable Transmission of START/ Stop Character MSI/Plessey Enable Code Standard Code 16K Enable 16K Code Disable 16K Code Digit Selection Symbol Function Symbology Identifiers 06656 Bology identifiers Programming Symbol EAN-13 Code Symbology IdentifiersStandard 2/5 Code MSI/Plessey Select Code Type Wand Emulation ParametersBar Code Polarity Transmission Rate Inches per second# Data Synchronization Disable Data # Synchronization Enable Data Synchronization Active # Polarity High Active Polarity Low Memory Module Disable Memory Module*# Enable Memory Module Setup Marker Beam Enable Marker Beam Disable Marker Beam 06656 Scanner Labeling Service and WarrantyHazardous visible light exposure Cleaning MaintenanceInspection PSC Website Support PSC Website TekForum Technical SupportReseller Technical Support Telephone Technical Support Hexadecimal Conversion Table Appendix a Part a Part B Ascii HEX Function Primary Function Key Table PC/AT, PC/XT, IBM 3151, and IBM PS/2 Model 57/25 Secondary Function Key Tables IBM 3171/3181/3191 and IBM VT220/320/420 Apple MacIntosh 06656 User’s / Programming Guide Declaration of Conformity PSC Inc