Manuals / Dell / Computer Equipment / Personal Computer

Dell DCDO, 710 H2C service manual Installing a CD/DVD Drive

Models: 710 H2C DCDO

1 87

Download 87 pages 31.98 Kb

Page 52

Installing a CD/DVD Drive

1

drive release latch

2

CD/DVD drive

6.Replace the drive panel (see Replacing the Drive Panel).

7.Replace the computer cover (see Replacing the Computer Cover).

NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.

8. Connect the computer and devices to electrical outlets, and turn them on.

Installing a CD/DVD Drive

1.Follow the procedures in Before You Begin.

2.Remove the computer cover (see Removing the Computer Cover).

3.Remove the drive panel (see Removing the Drive Panel).

4.Remove the existing CD/DVD drive, if applicable (see Removing a CD/DVD Drive).

5.Prepare the CD/DVD drive for installation and check the documentation that accompanied the drive to verify that the drive is configured for your computer.

NOTE: If you are installing an IDE drive, configure the drive for the cable select setting.

6.If no screws are attached to the drive, check the inside of the drive panel for screws and, if screws are present, attach the screws to the new drive.

Image 52

Dell DCDO, 710 H2C service manual Installing a CD/DVD Drive

Contents

Dell XPS 710 H2C Edition Service Manual Technical Overview Removing and Installing PartsReplacing the Computer Cover Advanced Troubleshooting System Setup Technical SpecificationsDell XPS 710 H2C Edition Service Manual Back to Contents PageConnectors About Your XPS ComputerFront I/O Connectors System SetupBack I/O Connectors see System SetupBack I/O Connectors Back ViewGreen - A good connection exists between a 10-Mbps network and Back to Contents Page see System SetupUse the blue line-in connector to attach a record/playback device such as Before You Begin Getting StartedRecommended Tools Preparing to Work Inside Your Computerb. In the Turn off computer window, click Turn off a. Click Start, then click Turn Off ComputerBack to Contents Page Removing the Computer Cover Dell XPS 710 H2C Edition Service ManualBack to Contents Page Back to Contents PagePower Supply PSU DC Connector Pin Assignments Technical OverviewInside View of Your Computer System Board Components1 white memory module connectors DIMM1 Power Supply PSU DC Connector Pin Assignments DC Power Connector P1DC Power Connector P2 1-KW Power Supply750-KW Power Supply SignalDC Power Connector P3 Graphics Card 1-KW Power Supply750-KW Power Supply SignalDC Power Connector P4 Graphics Card DC Power Connector P5 FD122-AWG Wire +5 VDCDC Power Connector P6 and P7 BAY1 and Bay2 DC Power Connectors P8 and P9 HDD0 and HDD1DC Power Connectors P10-P13 HDD2 and HDD5 1-KW Power SupplyDC Power Connectors P14 Peripheral DC Power Connector P15 Graphics Card - 1-KW PSU OnlySignal Name 18-AWG Wire ColorDC Power Connector P16 Graphics Card - 1-KW PSU Only Signal Name18-AWG Wire Color Back to Contents PageRemoving and Installing Parts Liquid Cooling Assembly Processor Battery Removing the Computer StandBefore You Begin Before You Begin Removing the Computer Cover Memory Cards Drivesa. Click Start, then click Turn Off Computer Removing the Computer Coverb. In the Turn off computer window, click Turn off Inside View of Your Computer 1 computer cover2 cover release latch 3 cover hinge tabsSystem Board Components CD/DVD drive baysfloppy drive/media card reader 3 hard drive bayswhite memory front panel 1394a connectorMemory DDR2 Memory OverviewAddressing Memory Configurations Installing Memorycutouts Cards Removing MemoryRemoving PCI and PCI Express Cards PCI Express x16 card slotrelease tab Installing PCI and PCI Express Cards release tab Removing a PCI Express Graphics Card from a Dual Configuration 1 graphics card bridge Installing a PCI Express Graphics Card in a Dual Configuration 1. Follow the procedures in Before You Begin 1 PCI Express x16 card 2 securing tab3 PCI Express x16 card slot 9. Connect any cables that should be attached to the cardNetwork Adapter and Sound Card Settings DrivesGeneral Drive Installation Guidelines About Serial ATA Drivessystem board 1 CD/DVD drive baysHard Drive Removing a Hard Drivepower cable 5. Ensure that all connectors are properly cabled and firmly seatedblue tabs hard driveInstalling a Hard Drive hard drive bracket7. Connect the power cable to the hard drive hard drive8. Connect the hard drive data cable to the hard drive hard drive bayRemoving the Drive Panel Drive PanelReplacing the Drive Panel Floppy Drive Removing a Floppy Drivepower cable drive release latch6. Replace the drive panel see Replacing the Drive Panel floppy drive data cableInstalling a Floppy Drive Media Card Reader Removing a Media Card Reader1 media card reader power cable 2 system board connectordrive release latch 6. Replace the drive panel see Replacing the Drive PanelInstalling a Media Card Reader shoulder screwsCD/DVD Drive Removing a CD/DVD Drivepower cable 4. Disconnect the power and data cables from the back of the drivedata cable Installing a CD/DVD Drive To locate the system board connector, see System Board Components Attach the power and data cables to the CD/DVD driveCD/DVD drive shoulder screwsLiquid Cooling Assembly Removing the Liquid Cooling AssemblyPage TECPUMP Installing the Liquid Cooling Assembly Processor Installing the ProcessorRemoving the Processor 1. Unpack the new processor Replacing the Battery BatteryRemoving the Computer Stand Replacing the Computer Cover Back to Contents Page hinge slotsDell XPS 710 H2C Edition Service Manual Replacing the Computer CoverBack to Contents Page Back to Contents Page Advanced Troubleshooting Power LightsPower Lights Diagnostic Lights Beep Codes System Messages Dell DiagnosticsDiagnostic Lights ProblemSuggested Resolution Light PatternBeep Codes MemoryManual Express CardsSystem Messages MessagePossible Cause Corrective ActionDell Diagnostics When to Use the Dell DiagnosticsStarting the Dell Diagnostics From Your Hard Drive Starting the Dell Diagnostics From the Drivers and Utilities CD7. At the CD-ROM Startup Menu highlight Boot from CD-ROM OptionFunction Dell Diagnostics Main MenuBack to Contents Page devices attached to your computerParameters Custom Test onlySystem Setup Entering System SetupSystem Setup Screens Overview Entering System Setup System Setup Options Boot SequenceSystem Setup Options Options ListSystem DrivesOnboard Devices booting to an operating system located onanother computer. If a boot routine is not Off - Integrated audio is disabledLEDs see About Your XPS Computer PerformanceSecurity Off - Multiple CPU core technologyOn - Multiple CPU core technology CPU clock speed so that the CPU operatesPower Management Power Timetime set in Auto Power Time TimeMaintenance Setup & Boot Menu defaultSetup & Boot Menu - Display both messages F2=Setup and F12=Boot Menu POST BehaviorBoot Sequence Option SettingsChanging Boot Sequence for the Current Boot Changing Boot Sequence for Future Bootsa. Click Start, then click Turn Off Computer Clearing Forgotten Passwordsb. In the Turn off computer window, click Turn off Clearing CMOS Settings Back to Contents PageTechnical Specifications ProcessorMemory NOTE See Addressing MemoryConnectors Expansion BusAvailable devices Serial ATA drive, floppy driveDiagnostic Lights Controls and LightsPower DC power supplyoverload an electrical outlet, power power strip, or other receptacleBack to Contents Page