Manuals / Delta / Lawn and Garden / Pole Saw

Delta 36-978 Constructing A Push Stick, Thanlesswidthof Materialtobecut, OR3/4, Offcuthereto

Models: 36-978

1 37

Download 37 pages 14.28 Kb

Page 34

CONSTRUCTING A PUSH STICK

CONSTRUCTING A PUSH STICK

WHEN RIPPING WORK LESS THAN 6 INCHES WIDE, A PUSH STICK SHOULD BE USED TO COMPLETE THE FEED AND COULD EASILY BE MADE FROM SCRAP MATERIAL BY FOLLOWING

THE PATTERN SHOWN IN FIG. S25.

PUSH STICK

"
OR3/4	ORWOODTHICKNESS	THANLESSWIDTHOF MATERIALTOBECUT
FROMMAKE1/2	ORWOODTHICKNESS	THANLESSWIDTHOF MATERIALTOBECUT
"

FROM SLIPPING

PREVENT HAND

NOTCH TO HELP

OFFCUTHERETO	WOOD	HEREOFFCUT TO	WOOD	1/2
OFFCUTHERETO	PUSH1/4	HEREOFFCUT TO	PUSH1/2	1/2
	"		"	SQUARES
				"

Fig. S25

34

Image 34

Delta 36-978 Constructing A Push Stick, Thanlesswidthof Materialtobecut, OR3/4, From Slipping Prevent Hand, Offcuthereto

Contents

10 Contractor’s Saw For Parts, Service, Warranty or other AssistanceTo learn more about DELTA MACHINERY INSTRUCTION MANUALIMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTSSAVE THESE INSTRUCTIONS TOOL WARNING LABELS SAFETY GUIDELINESCALIFORNIA PROPOSITION GENERAL SAFETY RULES ADDITIONAL SPECIFIC SAFETY RULES FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURYMOTOR SPECIFICATIONS POWER CONNECTIONSGROUNDING INSTRUCTIONS MINIMUM GAUGE EXTENSION CORD EXTENSION CORDSMINIMUM GAUGE EXTENSION CORD FOREWORD CARTON CONTENTSFUNCTIONAL DESCRIPTION TABLE SAW PARTSMODEL 2 SHEET METAL EXTENSION WINGS EXTENSION WINGSSTAND AND MOBILE BASE PARTS MODEL 2 CAST IRON EXTENSION WINGSASSEMBLY TOOLS REQUIRED ASSEMBLYUNPACKING AND CLEANING ASSEMBLY TIME ESTIMATEMOBILE BASE AND STAND ASSEMBLY 13. Fig. 20 shows the leveling feet and the wheels properly assembled THE WHEELS WILL BE INSTALL ED INSIDE THESE BRACKETS11. Take leveling feet shown at 33 in Fig 5/16-18 Nylock Nut V FigMOBILE BASE AND STAND ASSEMBLY TO SAW DUST CHUTE AND BACK BRACEWRENCH HOOK BLADE TILTING AND RAISING HANDWHEELMOTOR TO MOTOR MOUNTING PLATE MOTOR AND MOTOR MOUNTING PLATE TO SAW MOTOR PULLEY, PULLEY GUARD, AND DRIVE BELT4. Place a ¼ External Tooth Lockwasher onto a ¼-20 CONNECTING MOTOR CORD TO SWITCH ASSEMBLY REMOVING MOTOR FOR TRANSPORTBLADE GUARD AND SPLITTER ASSEMBLY AND ALIGNMENT G H C 10. Using a straight edge, check to see if the rear of the splitter G is aligned with the saw blade, as shown in Fig. 51. If alignment is necessary, loosen the screws B Fig. 43, align splitter G with the saw blade, and tighten two screws B Fig EXTENSION WINGSLOCKING SWITCH IN THE “OFF” POSITION OPERATIONAL CONTROLS AND ADJUSTMENTSON/OFF SWITCH OPERATIONRAISING AND LOWERING BLADE ADJUSTING 90 DEGREE AND 45 DEGREE POSITIVE STOPSOVERLOAD PROTECTION TILTING THE BLADEADJUSTING TABLE INSERT MITER GAUGE OPERATION AND ADJUSTMENTASSEMBLING MITER GAUGE ALIGNING MITER SLOTS TO BLADE CHANGING THE SAW BLADEBACKLASH ADJUSTMENTS FOR BLADE RAISING AND BLADE TILTING MECHANISMS QUICK OPERATIONS CHECKLISTMACHINE USE KEY PARTS AND SAFETY FEATURES ON YOUR SAW CROSS-CUTTING BLADE GUARD AND SPLITTER USEA Fig. S1 Fig. S2 C A Fig. S3 BEVEL CROSSCUTTING MITERINGCOMPOUND MITERING RIPPING USING MOULDING CUTTERHEAD BEVEL RIPPINGUSING ACCESSORY DADO HEAD USING AUXILIARY WOOD FACING TROUBLESHOOTING CONSTRUCTING A FEATHERBOARDPUSH STICK CONSTRUCTING A PUSH STICKTHANLESSWIDTHOF MATERIALTOBECUT OR3/4SHELF MEASUREMENTS MAINTENANCEKEEP MACHINE CLEAN FAILURE TO STARTWARRANTY SERVICEACCESSORIES Two Year Limited New Product WarrantyDelta Machinery