Manuals / Delta / Lawn and Garden / Pole Saw

Delta 36-978 Extension Wings, Stand And Mobile Base Parts, MODEL 2 SHEET METAL EXTENSION WINGS

Models: 36-978

1 37

Download 37 pages 14.28 Kb

Page 9

Image 9

EXTENSION WINGS

MODEL 36-978

2 SHEET METAL

EXTENSION WINGS

MODEL 36-979

2 CAST IRON EXTENSION

WINGS

Fig. 2

STAND AND MOBILE BASE PARTS

2829

Fig. 3

24.Plastic Foot (4)

25.Corner Bracket (left side)

26.Corner Bracket (right side)

27.Wheel (2)

28.Short Side Leg Support (2)

29.Long Side Leg Support (2)

30.Leg (4)

31.Short Panels For Back and Front (2)

32.Long Panels for Sides (2)

33.Leveling Feet (2)

34.Foot Lever Assembly

35.Caster Assembly

Page 9

Image 9

Delta 36-978 instruction manual Extension Wings, Stand And Mobile Base Parts, MODEL 2 SHEET METAL EXTENSION WINGS, 2829

Contents

To learn more about DELTA MACHINERY For Parts, Service, Warranty or other Assistance10 Contractor’s Saw INSTRUCTION MANUALTABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONSSAVE THESE INSTRUCTIONS SAFETY GUIDELINES TOOL WARNING LABELSCALIFORNIA PROPOSITION GENERAL SAFETY RULES FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY ADDITIONAL SPECIFIC SAFETY RULESPOWER CONNECTIONS MOTOR SPECIFICATIONSGROUNDING INSTRUCTIONS EXTENSION CORDS MINIMUM GAUGE EXTENSION CORDMINIMUM GAUGE EXTENSION CORD FUNCTIONAL DESCRIPTION CARTON CONTENTSFOREWORD TABLE SAW PARTSSTAND AND MOBILE BASE PARTS EXTENSION WINGSMODEL 2 SHEET METAL EXTENSION WINGS MODEL 2 CAST IRON EXTENSION WINGSUNPACKING AND CLEANING ASSEMBLYASSEMBLY TOOLS REQUIRED ASSEMBLY TIME ESTIMATEMOBILE BASE AND STAND ASSEMBLY 11. Take leveling feet shown at 33 in Fig THE WHEELS WILL BE INSTALL ED INSIDE THESE BRACKETS13. Fig. 20 shows the leveling feet and the wheels properly assembled 5/16-18 Nylock Nut V FigDUST CHUTE AND BACK BRACE MOBILE BASE AND STAND ASSEMBLY TO SAWBLADE TILTING AND RAISING HANDWHEEL WRENCH HOOKMOTOR TO MOTOR MOUNTING PLATE MOTOR PULLEY, PULLEY GUARD, AND DRIVE BELT MOTOR AND MOTOR MOUNTING PLATE TO SAW4. Place a ¼ External Tooth Lockwasher onto a ¼-20 REMOVING MOTOR FOR TRANSPORT CONNECTING MOTOR CORD TO SWITCH ASSEMBLYBLADE GUARD AND SPLITTER ASSEMBLY AND ALIGNMENT G H C EXTENSION WINGS 10. Using a straight edge, check to see if the rear of the splitter G is aligned with the saw blade, as shown in Fig. 51. If alignment is necessary, loosen the screws B Fig. 43, align splitter G with the saw blade, and tighten two screws B FigON/OFF SWITCH OPERATIONAL CONTROLS AND ADJUSTMENTSLOCKING SWITCH IN THE “OFF” POSITION OPERATIONOVERLOAD PROTECTION ADJUSTING 90 DEGREE AND 45 DEGREE POSITIVE STOPSRAISING AND LOWERING BLADE TILTING THE BLADEMITER GAUGE OPERATION AND ADJUSTMENT ADJUSTING TABLE INSERTASSEMBLING MITER GAUGE CHANGING THE SAW BLADE ALIGNING MITER SLOTS TO BLADEQUICK OPERATIONS CHECKLIST BACKLASH ADJUSTMENTS FOR BLADE RAISING AND BLADE TILTING MECHANISMSMACHINE USE KEY PARTS AND SAFETY FEATURES ON YOUR SAW BLADE GUARD AND SPLITTER USE CROSS-CUTTINGA Fig. S1 Fig. S2 C A Fig. S3 MITERING BEVEL CROSSCUTTINGCOMPOUND MITERING RIPPING BEVEL RIPPING USING MOULDING CUTTERHEADUSING ACCESSORY DADO HEAD USING AUXILIARY WOOD FACING CONSTRUCTING A FEATHERBOARD TROUBLESHOOTINGTHANLESSWIDTHOF MATERIALTOBECUT CONSTRUCTING A PUSH STICKPUSH STICK OR3/4KEEP MACHINE CLEAN MAINTENANCESHELF MEASUREMENTS FAILURE TO STARTACCESSORIES SERVICEWARRANTY Two Year Limited New Product WarrantyDelta Machinery