Manuals / Delta Tau / Computer Equipment / Computer Hardware

Delta Tau PMAC2A-PC/104 manual J3 JMACH1 50-Pin-Header

Models: PMAC2A-PC/104

1 70

Download 70 pages 39.45 Kb

Page 62

PMAC2A PC104 Hardware Reference Manual

J3 JMACH1 (50-Pin-Header) (Continued)

Top View

Pin#	Symbol	Function	Description	Notes
40	DAC8/	Output	Analog Out Negative 8	4,5
41	AENA7/	Output	Amplifier-Enable 7
42	AENA8/	Output	Amplifier -Enable 8
43	FAULT7/	Input	Amplifier -Fault 7	6
44	FAULT8/	Input	Amplifier -Fault 8	6
45	ADCIN_1	Input	Analog Input 1	Option-2 required
46	ADCIN_2	Input	Analog Input 2	Option-2 required
47	FLT_FLG_V	Input	Amplifier Fault pull-up V+
48	GND	Input	Analog Common
49	A+15V	Input	DACs +15V Supply
50	A-15V	Input	DACs -15V Supply

The J3 connector is used to connect PMAC to the second 4 channels (Channels 5, 6, 7, and 8) of servo amps and encoders.

Note 1: In standalone applications, these lines can be used as +5V power supply inputs to power PMAC’s digital circuitry.

Note 2: Referenced to digital common (GND). Maximum of ±12V permitted between this signal and its complement.

Note 3: Leave this input floating if not used (i.e. digital single-ended encoders).

Note 4: ±10V, 10 mA max, referenced to common ground (GND).

Note 5: Leave floating if not used; do not tie to GND.

Note 6: Functional polarity controlled by variable Ix25. Must be conducting to 0V (usually GND) to produce a 0 in PMAC software. Automatic fault function can be disabled with Ix25.

56	Acc-1P Connector Pinouts

Image 62

Delta Tau PMAC2A-PC/104 manual J3 JMACH1 50-Pin-Header

Contents

PMAC2A-PC/104 Copyright Information Delta Tau Data Systems, Inc. Technical SupportTable of Contents Software Setup Base Board Connector Pinouts PMAC2A PC104 Hardware Reference Manual Table of Contents Board Configuration IntroductionAcc-1P Option 1 I/O Ports Option 12 Analog-to-Digital ConvertersAcc-1P Axis Expansion Piggyback Board Acc-1P Option 2 Analog-to-Digital ConvertersAcc-2P Option 1B Ethernet Interface Acc-2P Communications BoardAcc-2P Option 1A USB Interface Acc-2P Option 2 Dpram CircuitryPMAC2A PC104 Hardware Reference Manual Introduction Board Reset Jumpers Base Board Hardware SetupClock Configuration Jumpers Resistor Packs Configuration CPU Jumper ConfigurationConfiguration Jumpers Communication JumpersDevice Resistor Pack Pack Size PMAC2A PC104 Hardware Reference Manual E0 Reserved for future use ACC-1P Hardware SetupReserved Configuration Jumpers Handwheel Encoder Termination Resistors Jopt Connector E10 MOx MIx Lines ACC-2P Hardware SetupJthw Connector DATx SELx Differential or Single-Ended Handwheel Encoder Selection DAC Outputs Power Supply Power SuppliesDigital Power Supply Machine ConnectionsOvertravel Limits and Home Switches Motor Signals ConnectionsPulse and Direction Stepper Drivers DAC Output SignalsAmplifier Enable Signal AENAx/DIRn ExampleAmplifier Fault Signal Fault Acc-1P General-Purpose Digital Inputs and Outputs J7 PortAcc-2P Thumbwheel Multiplexer Port Jthw Port Acc-2P General-Purpose Digital Inputs and Outputs Jopt PortAcc-1P Thumbwheel Multiplexer Port J2 Port Compare Equal Outputs Acc-1P or Acc-2P Handwheel Port JHW / PD PortOptional Analog Inputs Serial Port JRS232 Port Acc-2P Ethernet RJ45 Connector J10 PortAcc-2P USB Connector J1 Port PC DB-9Machine Connections Example Using Analog ±10V Amplifier PMAC2A PC104 Hardware Reference Manual PMAC2A PC104 Hardware Reference Manual Machine Connections Communications Software SetupOperational Frequency and Baud Rate Setup Pmac I-VariablesI54 Baud Rate for Filtered DAC Outputs ConfigurationI54 Baud Rate Acc-1P with Jumper E6 on Position Using Flag I/O as General-Purpose I/OGeneral-Purpose Digital Inputs and Outputs Flag Type Channel NumberAcc-2P with Jumper E5 in Position Open PLC1 ClearThumbwheel Port Digital Inputs and Outputs Acc-1P with Jumper E6 in PositionAcc-1P Analog Inputs Analog Inputs SetupBaseboard Analog Inputs Board Dimensions Base Board Hardware Reference SummaryBoard Layout FeatureFeature Location Connectors and Indicators Page ACC-1P Hardware Reference Summary TB1 JMACH1 J8 Handwheel / Pulse and Direction Port JHW / PD Port J2 Thumbwheel Multiplexer Port Jthw PortJ7 General-Purpose Digital Inputs and Outputs Jopt Port Page ACC-2P Hardware Reference Summary TB1 Jthw Jopt J10 Ethernet Communications Port J1 USB Communications PortJ8 Handwheel/Pulse and Direction Port JHW / PD Port Page E3 Normal/Re-Initializing Power-Up/Reset E0 Forced Reset ControlE1 Servo and Phase Clock Direction Control Base Board E-POINT Jumper DescriptionsE10 E12 Power-Up State Jumpers E8 Phase Clock Lines Output EnableE9 Servo Clock Lines Output Enable Description DefaultE16 ADC Inputs Enable E13 Power-Up/Reset Load SourceE14 Watchdog Disable Jumper E15A, B, C Flash Memory Bank SelectPoint and Physical Location Description Default Layout E18 E19 PC/104 Bus AddressE0 Reserved for Future Use E1 E2 Machine Output Supply Voltage ConfigureACC-1P E-POINT Jumper Descriptions E3 E4 JHW, PD Function SelectE7 Machine Input Source/Sink Control E5 Servo Gate Address SelectE6 I/O Gate Address Select E5 I/O Gate Address Select E1 USB/Ethernet Micro-Controller Firmware Reload EnableACC-2P E-POINT Jumper Descriptions E6 Communications Port SelectPoint and Physical Location Description Default E7- E10 Ports Direction ControlJ4 JRS232 Serial Port Connector Base Board Connector PinoutsTB1 Jpwr Power Supply Pin# Symbol Function DescriptionJ3 JMACH1 Machine Port Connector J3 JMACH1 50-Pin Header J4 JMACH2 Machine Port Baseboard Connector ACC-1P Connector Pinouts J2 Jthw Multiplexer Port Connector Pin# SymbolJ3 JMACH1 Machine Port Connector Pin Header J3 JMACH1 50-Pin-Header Connector 34-Pin Header FLG78VJ7 Jopto I/O Port Connector J8 JHW Handwheel Encoder Connector Page J1 USB Universal Serial Bus Port Optional ACC-2P Connector PinoutsPin # Symbol Function Pin Connector J7 Jopt I/O Port Connector J10 Ethernet Port Optional Pin # Function