ENGLISH
Getting |
|
| Installing/Setting the Speakers |
| |||
|
|
|
|
|
| ||
sSet the “Amp Assign” Mode According to the Speaker Layout. |
| ||||||
Started |
| ||||||
The signals output from the |
| ||||||
switched to signals of the surround mode being used (vpage 25 “Amp Assign”). |
| ||||||
|
|
| |||||
Connections |
|
|
|
|
|
|
|
| Amp assign mode | SURR. BACK/AMP ASSIGN | Example of speaker installation |
| |||
| (vpage 25) | Speaker connections |
| ||||
|
|
|
|
| |||
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
Settings | Normal | Surround back |
|
|
|
| |
speakers |
|
|
|
| |||
|
|
|
|
| |||
|
|
|
|
|
| ||
Playback |
|
|
|
|
|
| |
|
|
| (7.1) |
|
| ||
|
|
|
|
|
| ||
| Surround back |
|
|
|
| ||
| speakers |
|
|
|
| ||
Normal | b Connect to the “L” |
|
|
|
| ||
Zone |
| speaker terminal. |
|
|
|
| |
| b Set “Surround Back” |
|
|
|
| ||
|
|
| (vpage 26) to “1spkr”. |
|
|
|
|
Remote |
|
| (6.1) |
|
| ||
|
|
|
|
|
| ||
| Not connected |
|
|
|
| ||
Control |
|
|
|
|
| ||
Normal | b Set the “Surround Back” |
|
|
|
| ||
setting (vpage 26) to |
|
|
|
| |||
|
|
|
|
| |||
Information |
| “OFF”. |
|
|
|
| |
|
|
|
|
|
| ||
|
|
| (5.1) |
|
| ||
|
|
|
|
|
| ||
| Front Height |
|
|
|
| ||
Troubleshooting | Front Height |
|
|
|
| ||
speakers |
|
|
|
| |||
|
|
|
|
| |||
|
|
|
|
|
| ||
|
|
| (7.1) |
|
| ||
|
|
|
|
|
| ||
|
|
|
|
|
| ||
Subwoofer with | Front speakers | Front speakers | Center | Surround |
builtin amplifier | A | B | speaker | speakers |
(L) | (R) | (L) | (R) | (L) | (R) |
w q |
| ||||
|
|
|
|
| |
w | q w q | w q | w q | w | q w q |
*/ |
|
|
| ||
|
|
|
|
|
For connections of the SURR. BACK/AMP ASSIGN speaker terminals, see “Amp Assign” (vpage 25).
Protection circuit
|
| Front A or B |
|
|
|
|
| |
Specifications | Front A | speakers |
|
|
|
|
| |
b For connections, |
|
|
|
|
| |||
or |
|
|
|
|
| |||
see “About |
|
|
|
|
| |||
Front B |
|
|
|
|
| |||
connections” |
|
|
|
|
| |||
|
|
|
|
|
| |||
| (vpage 12). |
|
|
|
|
| ||
|
| (5.1) |
|
| ||||
|
|
|
|
|
|
|
|
|
|
| MAIN ZONE | ZONE2 | |||||
| ZONE2 | ZONE2 speakers |
|
|
|
|
| |
| (Default) |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
| (2) |
| |
|
|
| (5.1) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If the core wires touch the rear panel and the screws etc., or the ± sides touch each other, the protection circuit will be activated and the power indicator will flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker output is isolated, and the power supply goes to the standby state. If the power supply is turned off, after the power supply cord is withdrawn, please confirm that speaker cable and input cable are connected.
Also, if replaying large sound levels by using a speaker having an impedance less than that
specified (eg, 4 Ω/ohms), the temperature will rise, and the protection circuit might be activated. The power supply will go into the standby state, and the power indicator will flash red at 2 second intervals. In this case, please switch off the power supply, and wait until the
Even if there are no problems with the surrounding ventilation and connections, in the event of the protection circuit becoming activated,
due to thinking that the
11