ENGLISH

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

Error Messages

If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure over again.

Check Audyssey Auto Setup Measurement Results (Parameter Check)

This is displayed after the Audyssey Auto Setup procedure is completed.

NOTE Be sure to turn the power off before checking the speaker connections.

 

Error messages (examples)

Cause

Measures

Caution

 

• Included setup microphone is not connected.

• Connect the included setup microphone to the

 

 

MultEQ

 

SETUP MIC jack on the main unit.

 

FMicrophone:None

 

 

• Not all speakers could be detected.

• Check the speaker connections.

 

or

 

 

Speaker

:None

• The front L speaker was not properly detected.

 

 

Retry

 

 

 

 

 

 

 

Cancel

 

 

 

[ENT]:Retry

 

 

 

 

 

 

 

 

Caution

 

• Too much noise in the room for accurate

• Either turn off any device generating noise or

 

 

MultEQ

measurements to be made.

move it away.

1Press ui to select “Parameter Check”, then press .

“Parameter Check” is displayed on the on-screen display.

3-2.Parameter Check

Speaker Config.Check

Distance Chenck

Channel Level Check

Crossover Freq.Check

EQ Check

Restore

[ENT]:Select [RTN]:Back

Front

 

 

FAmbient noise is

 

 

• Try again when the surroundings are quieter.

 

 

too high or

 

 

 

 

 

 

Level is too low.

 

• Speaker or subwoofer sound is too low for

• Check the speaker installation and the direction

 

 

 

 

 

 

 

 

 

 

 

 

 

accurate measurements to be made.

in which the speakers are facing.

 

 

 

 

Retry

 

 

 

 

• Adjust the subwoofer’s volume.

 

 

 

 

Cancel

 

 

 

 

 

 

 

[ENT]:Retry

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Caution

 

 

MultEQ

• Displayed speaker could not be detected.

• Check the connections

of

the displayed

 

 

 

 

 

 

· The front R speaker were not properly detected.

speaker.

 

 

 

 

 

 

 

 

 

· Only one channel of the surround speakers was

 

 

 

 

 

 

Front

 

 

 

 

 

 

 

 

 

R

:None

 

 

 

detected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Retry

 

 

 

· Sound was output from the R channel when only

 

 

 

 

 

 

Cancel

 

 

 

one surround back speaker was connected.

 

 

 

 

 

 

Skip

 

 

 

 

 

 

 

 

 

 

 

 

· The surround back, but the surround speaker was

 

 

 

[

]:Up/Down [

]:CH

 

 

 

 

 

 

 

 

 

 

 

not detected.

 

 

 

 

Caution

 

 

 

 

• Displayed speaker connected with the polarities

• Check the polarities of the displayed speaker.

 

 

 

MultEQ

reversed.

• For some speakers, this

error

message may

 

 

 

 

 

 

 

 

 

 

 

 

 

 

be displayed even if the speaker is properly

 

 

 

Front

 

 

 

 

 

 

 

L

:Phase

 

 

connected. If you are sure that the wiring is

 

 

 

Retry

 

 

 

 

correct, press ui to select “Skip”, then press

 

 

 

Cancel

 

 

 

 

.

 

 

 

 

 

Skip

 

 

 

 

 

 

 

[

]:Up/Down [

]:CH

 

 

 

 

2Use ui to select the item you want to check, then press .

 

Speaker Config. Check

: Check the speaker configuration

 

 

 

 

Distance Check

: Check the distance

 

 

 

 

Channel Level Check

: Check the channel level

 

 

 

 

Crossover Freq. Check

: Check the crossover frequency

 

 

 

 

EQ Check

: Check the equalizer

 

 

 

3Use o p to switch the display between the different speakers.

4 Press .

The confirmation screen reappears. Repeat steps 2 and 3.

Even if the settings are changed after the Audyssey Auto Setup procedure, the Audyssey Auto Setup settings can be restored by selecting “Restore” then pressing .

Specifications Troubleshooting Information Control Remote Zone-Multi Playback Settings Connections Started Getting

nTo perform the Audyssey Auto Setup procedure again

Press ui to select “Retry”, then press .

nTo cancel Audyssey Auto Setup

Use ui to select “Cancel”, then select “Yes” using o p.

24