Denon AVR-3801 Enter Code, Code no, Learn, Reset, Auto Search, DVD VDP Cable DBS VCR2, Jerrold

Preset memory

By using the preset memory, the included remote control unit can be used to control other makes of video equipment. Note that this is not possible for some models, however. In such cases, use the learning function (see page 34) to store the remote control signals in the remote control unit’s memory.

See page 37 for instructions on resetting the data stored in the preset memory.

1	Press the power ON/SOURCE button and the OFF button at
	the same time.
	• “SET UP” appears on the remote control unit’s display.

OFF	ON /
	SOURCE

				POWER
1	OFF			ON /
				SOURCE
		RC-883
		REMOTE CONTROL UNIT
	TV	CD CDR/MD/ TAPE RECEIVER
	VCR	DBS/CABLE	VDP	DVD

2	Press the ENTER button. ENTER
	SHIFT

3, 4 2, 3, 4

DISPLAY		MENU
SURR.		OSD
PARA.
SETUP		RETURN
	TUNING	A/B
		MEMORY
BAND		MODE
CHANNEL		VOLUME
+	TUNING	+
SKIP	ENTER
-	SHIFT	-
SKIP	MUTING

TUNER PHONO CD

1 2 3

3	Use the D and H cursor buttons to display “ENTER CODE” on
	the remote control unit, then press the ENTER button.
	The remote control unit’s display switches as follows each
	time the D and H cursor buttons are pressed.
	ENTER CODE		TUNING
	CODE NO	BAND	MODE
			TUNING

5	CDR/TAPE	VDP	DVD
	4	5	6
	VCR-1	VCR-2/V.AUX	TV/DBS
	7	8	9
	TV/	0	+10
	VCR
	TEST	SPEAKER	OUTPUT
	TONE
		SURROUND
	DOLBY/DTS	DSP	5CH / 7CH
	SURROUND	SIMU.	STEREO
	6.1 / 7.1	DIRECT	STEREO
	SURROUND
		INPUT
	MODE	ANALOG	EXT.IN
	SYSTEM CALL
	CALL 1	CALL 2	BACKLIGHT

	LEARN
	SYS CALL
		ENTER
	RESET	SHIFT	5
	AUTO SEARCH			1	2	3
4	After “SEL MODE” is displayed, the last selected mode is			4	5	6
	set. Use the D and H cursor buttons to display the component			7	8	9
	whose codes you want to store in the memory, then press
	the ENTER button.				0

TUNING

ENTER

Referring to the included List of Preset Codes, use the number buttons to input the preset code (a

4-digit number) for the manufacturer of the component whose signals you want to store in the memory.

BANDMODE

SHIFT

6	“OK” is displayed when the signals are registered and the
	mode is terminated.

TUNING

The display switches as shown below each time the D	7	To store the codes of another component in the memory,
		repeat steps 1 to 6.
and H cursor buttons are pressed.

TV CD MD TAPE VCR

DVD VDPCABLEDBSVCR2

NOTES:

•The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control unit’s transmitting window while setting the preset memory.

•Depending on the model and year of manufacture, this function cannot be used for some models, even if they are of makes listed on the included list of preset codes.

•Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and check.

The preset codes are as follows upon shipment from the factory and after resetting:

TV, VCR	HITACHI
CD, MD, TAPE, CDR, VDP, DVD, DVD SETUP	DENON
DBS	GENERAL INSTRUMENT
CABLE	JERROLD

31