Desa E32, VE36, VE32 Electric Fireplace Installation Instructions, Connecting Heater Wires

10 ELECTRIC FIREPLACE INSTALLATION INSTRUCTIONS

Models: (V)E32L, (V)E32LB, (V)E32LH, (V)E32LBH (V)E36L, (V)E36LB, (V)E36LH and (V)E36LBH

OPTIONAL HEATER ACCESSORY Continued

13.Connect White heater wire to neutral connection marked ‘B’ or ‘A’ on terminal block. See partial wiring diagram, Figure 24.

14.Connect Black heater wire to terminal marked ‘N-1’on the heater power, switch (see Figure 25).

Note: On alternate style heaters the White and Black wires are connected common at terminal ‘N-1’(see Figure 26).

15.Connect Red heater wire to terminal marked ‘L-4’on heater power switch. See partial wiring diagram, Figure 25 or 26.

16.Connect one end of the Black jumper lead, provided in the kit, to the power connection marked ‘D’ on the terminal block and the other end to switch terminal marked ‘L-5’(see Figure 27).

17.Replace the 2 Hex screws on rear flanges of the blower mount.

18.Remount the harness strap to the blower mount, if removed.

19.Make sure all wires are clear of the heater discharge area, line up the mounting holes on the front blower mount to the holes in the control panel and replace the 2 black pan head screws.

20.Raise the control cover up and position the 2 locking tabs through the notched openings in the firebox top, then slide to the left until locked into position. See Figure 20, page 9.

21.Tuck any excess slack in harnesses into control cover, swing cover down to line-up mounting holes on control panel and replace the 2 Phillips screws removed prior.

22.Restore power to the unit and check operation of the heater.

IMPORTANT: Be sure to inspect the components and wiring for damage before connecting power to the unit. If any components are found damaged, contact an authorized dealer for original DESA replacement part(s) or call DESA at 1-866-872-6040 for referral.

	BLK (NOIR)	WHT (BLANC)	CUTOUT	MOTOR
GRN		WHT	COUPE-	MOTEUR
	BLK (NOIR)	(BLANC)	CIRCUIT

(VERTE)		D	C	B	A	(BLANC - ALTERNATIF)	WHT
	WHT (BLANC)		TERMINAL			WHT - ALTERNATE	(BLANC)
	HARNESS 4"	BLK

CABLAGE (10 cm) NOIR					BLK	RED
			L N 1 HEATER POWER		(NOIR)	(ROUGE)
SUPPLY		4
				COURANT DE		HEATER COIL
CONNECTION		5	L
	BLK			L'CHAUFFAGE	BLK	RADIATEUR
CONNEXION
	(NOIR)				(NOIR)
D'ALIMENTATION
WIRES TO HEATER CIRCUIT			RED
		(ROUGE)

FILS À CIRCUIT D'CHAUFFAGE

Figure 24 - Heater Circuit Connection Diagram

CONTROL PANEL

TERMINAL BLOCK

WHITE (A-B)

	HEATER/BLOWER
ROCKER	BLACK (N-1)
SWITCH	RED (L-4)

Figure 25 - Connecting Heater Wires

CONTROL PANEL

TERMINAL BLOCK

WHITE (A-B)

ROCKER	WHITE (N-1)
SWITCH
	RED (L-4)	HEATER/BLOWER

Figure 26 - Connecting Alternate Heater Wires

CONTROL PANEL

TERMINAL (D)

JUMPER LEAD

SWITCH

TERMINAL (L-5)

Figure 27 - Connecting Jumper Lead

For more information, visit www.desatech.com

111076-01C