Bios Setup Load Fail-Safe Defaults | DFI system board, 915g-tmgf

BIOS Setup

3.1.9 Load Fail-Safe Defaults

The “Load Fail-Safe Defaults” option loads the troubleshooting default values permanently stored in the ROM chips. These settings are not optimal and turn off all high performance features. You should use these values only if you have hardware problems. Highlight this option in the main menu and press <Enter>.

If you want to proceed, type <Y> and press <Enter>. The default settings will be loaded.

3

9 3

Image 93

DFI system board, 915g-tmgf, 915gv-tml user manual Bios Setup Load Fail-Safe Defaults

Contents

83800441 915G-TMGF 915GV-TML All Rights Reserved Copyright FCC and DOC Statement on Class B About this Manual Table of Contents Appendix C Troubleshooting Appendix B System Error MessagesAppendix a Enabling the Hyper-Threading Technology Introduction Processor SpecificationsChipset System Memory Onboard Audio Features Onboard VGA FeaturesOnboard LAN Features Hardware Monitor IDE Interface ConnectorsRear Panel I/O Ports Expansion Slots PCI Express Special Features of the System BoardIntel Graphics Media Accelerator Hyper-Threading Technology Functionality Requirements Channel Audio CPU Overheat Protection IrDA Interface Dual Function Power ButtonUSB Ports Wake-On-Ring Wake-On-LAN RTC Timer to Power-on the SystemWake-On-PS/2 Keyboard/Mouse Wake-On-USB Keyboard/Mouse Acpi STR AC Power Failure Recovery Package Checklist Hardware Installation Hardware Installation 915GV Channel a DDR 1 and DDR Channel B DDR 3 and DDR System Memory Bios Setting Dynamic Mode AddressingSingle Channel SC Virtual Single Channel VSC On the next Hardware Installation Hardware Installation Installing the Dimm Installing the CPU CPUOverview Tab Gold mark Pin 1 of the socket Once the CPU is in place, move the cover down Use only certified fan and heat sink Installing the Fan and Heat Sink Hole Jumper Settings Clear Cmos DataIf you encounter the following Type Y and press Enter Hardware Installation 2 PS/2 Power Select Hardware Installation USB Power Select Parallel Rear Panel I/O Ports13941 Line-in Line-out Mic-in Bios Setting Hardware Installation 1 PS/2 Mouse and PS/2 Keyboard Ports Hardware Installation Serial Port Standard Parallel Port Hardware Installation Parallel PortExtended Capabilities Port Enhanced Parallel Port Function Driver Installation Hardware Installation VGA Port Hardware Installation Ieee 1394 915G-TMGF only Hardware Installation USB Ports Hardware Installation PXE LAN Boot ROM Hardware Installation 7 RJ45 LAN Port Rear Panel Audio Hardware Installation Audio Rear Audio and Front AudioMic-in Pink As rear right/left speaker out Front Audio CD-in Internal Audio Connector I/O Connectors Hardware Installation 2 S/PDIF Connecting the Floppy Disk Drive Cable Hardware Installation Floppy Disk Drive Connector Hardware Installation Serial ATA Connectors Connecting the IDE Disk Drive Cable Hardware Installation IDE Disk Drive Connector Adding a Second IDE Disk Drive Hardware Installation IrDA Connector Hardware Installation Cooling Fan Connectors Hardware Installation Power Connectors Reset Reset Switch Hardware Installation Front Panel ConnectorsSpeaker Speaker Connector ATX-SW ATX Power Switch PWR-LED Power/Standby LED Hardware Installation PCI Express x16 and x1 Slots Bios Setup Award Bios Setup UtilityPress DEL to enter setup When you press Del, the main menu screen will appear Bios Setup Standard Cmos Features DateTime IDE HDD Auto Detection IDE Channel 0 Master/Slave and IDE Channel 1 Master/Slave Capacity Access ModeCylinder Head Video Non-fatal errorHalt On Base Memory Extended Memory Total MemoryDisplays the total memory available in the system Bios Setup Advanced Bios Features CPU Feature Delay Prior To ThermalTM2 Bus VID NX Bios Control Hard Disk Boot PriorityLimit Cpuid MaxVal Quick Power On Self Test This field is used to enable or disable the CPU’s L3 cacheVirus Warning CPU L1 & L2 Cache Boot Up NumLock Status Boot Up Floppy SeekSwap Floppy Drive Gate A20 Option Typematic Delay Msec Typematic Rate SettingApic Mode Typematic Rate Chars/Sec OS Select for Dram 64MB MPS Version Control for OSReport No FDD For WIN Options are Yes and No Bios Setup Advanced Chipset Features Dram Timing SelectableThis field is used to select the timing of the Dram Precharge Delay tRAS Dram RAS# to CAS# DelaySystem Bios Cacheable Video Bios Cacheable Memory Hole At 15M-16M PCI-E Compliancy ModePCI Express Root Port Func PCI Express Port 1 to PCI Express Port PEG Force 3.12 PEG/Onchip VGA ControlOn-Chip Video Memory Size On-Chip Frame Buffer Size Boot Display OnChip IDE Device Bios Setup Integrated Peripherals IDE DMA Transfer Access IDE HDD Block ModeOn-Chip Primary PCI IDE IDE Primary Master PIO and IDE Primary Slave PIO On-Chip Serial ATA Setting USB Controller Onboard DeviceUSB 2.0 Controller USB Keyboard Support Disabled Select this option when using a PCI sound card Auto Select this option when using the onboard audioThis field is used to enable or disable the onboard LAN AC97 Audio Super IO Device Power On Function Hot Key Power On KB Power On PasswordUart Mode Select UR2 Duplex Mode ECP Mode Use DMA Parallel Port ModeOnboard Parallel Port This is used to select a DMA channel of the parallel port Run Vgabios if S3 Resume Bios Setup Power Management SetupAcpi Function Acpi Suspend Type Video Off Method Power ManagementVideo Off In Suspend Suspend Type HDD Power Down Suspend ModeSoft-Off by PWR-BTTN CPU Thermal-Throttling Resume By Alarm Power On By RingDate of Month Alarm Wake-Up By PCI Card Reload Global Timer Events Time hhmmss Alarm Bios Setup 6 PnP/PCI Configurations Reset Configuration DataInit Display First Respectively Resources Controlled ByIRQ Resources 6.5 PCI/VGA Palette Snoop Maximum Payload Size Shutdown Temperature Bios Setup PC Health Status CPU Clock Ratio Bios Setup Frequency/Voltage ControlThis field is used to select the CPU’s frequency ratio Auto Detect PCI Clk CPU Clock Bios Setup Load Fail-Safe Defaults Type Y and press Enter to load the Setup default values Bios Setup Load Optimized Defaults Bios Setup Set Supervisor Password Bios Setup Set User Password Bios Setup Save & Exit Setup Bios Setup Exit Without Saving Updating the Bios 100 Supported Software Drivers, Utilities and Software Applications 102 Supported Software Intel Graphics Media Accelerator Driver Supported Software Realtek Audio Driver Supported Software Realtek LAN Driver Supported Software Hardware Monitor Supported Software Microsoft DirectX To install, please follow the steps below Installation Notes Supported Software Intel USB 2.0 DriversWindows System requires a minimum of 300 Watt ATX 12V power supply Enabling Hyper-Threading TechnologyEnabling Hyper-Threading Technology 110 111 Error Messages System Error MessageFloppy Disks fail Bios ROM checksum error System halted Keyboard error or no keyboard presentHard Disks fail Keyboard is locked out Unlock the key Troubleshooting Troubleshooting ChecklistMake sure that the monitor’s power switch is on Monitor/Display Floppy Drive Power Supply Hard disk failure Troubleshooting Hard Drive System Board Keyboard 118