DigiTech RP1000 16, Storing/Copying/Naming a Preset

16

To bypass amp/cabinet modeling in all presets, press the Amp/Cabinet Bypass button. When it is

lit, amp/cabinet modeling is bypassed in all presets.

Amp/Cabinet Bypass can be used in either Preset or Pedalboard mode.

Storing/Copying/Naming a Preset

When you’re done editing a preset, you should store your settings to any of the 100 User preset

locations (presets 1-00). The following steps tell you how to store changes to a preset or copy a

preset to a different location:

Press the

1. Store button once. The Store button LED blinks and the ﬁrst character in the

Display ﬂashes, indicating that you can now name your custom creation.

Use 2. Knob 1 to select the alpha-numeric character and Knob 2 to select the next charac-

ter location.

1. Press Store;

characters in Display

flash individually

2. Use Knobs to

name Preset

Once the desired name is shown in the display, press the 3. Store button again to enter the

second stage of the storing process. The red Display begins to ﬂash.

Select the User preset location where your new sound will reside using the

4. Up and Down

Footswitches. The displays show the preset name and User preset number about to be

overwritten.

4. Select destination

with UP and DOWN

Footswitches

3. Press Store again;

Preset number flashes

Press the 5. Store button again to save the changes.

The procedure for copying one preset to another preset location is the same. Use the Foot-

switches to select the preset that you want to copy, then follow steps 1-4 for storing a preset

as described above. Press either Edit button at any time to abort the Store procedure.

Contents

Main Page Table of Contents Section One - Introduction ............1 Section Two - Editing Functions .....14 Section Three - Effects and Parameters ......................................17 Section Four - Other Functions .....31 Warranty We at DigiTech are very proud of our products and back up each one we sell with the following 1 Section One - Introduction Getting Acquainted Included Items About the RP1000 Preset Mode and Pedalboard Mode A Tone Library (Knob 1) Effects Library (Knob 2) Effects Level (Knob 3) 3 1. 2. 3. 4 A Guided Tour of the RP1000 Front Panel 12345678 9 1 0 1 1 1 2 13 Page Page Rear Panel 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 3 8 Getting Started Making Connections Amp/Cabinet Bypass Amp Loop Connection Setups Mixer Stereo Amps Amp Loop with Pre-Amp In Line Stomp Loop Amp Loop using Guitar Amps Pre Amp Amp Loop and Stomp Loop Studio Setup (Computer and Personal Monitors) 14 Applying Power Section Two - Editing Functions Preset Mode and Pedalboard Mode 15 Editing/Creating Presets 1. Select a tone with the Tone Library knob 2. Select an effect or effects chain with the Effects Library knob 3. Adjust the effects level with the Effects Level knob 16 Storing/Copying/Naming a Preset 17 Section Three - Effects and Parameters About the Effects Effect Denitions Wah Compressor Distortion Knobs 2-6 have the following functions for the various Distortions: Amplier Page EQ Noise Gate/Auto Swell Chorus/FX Knobs 2-6 have the following functions for the various Chorus types: Page Page Page Page Page Delay Reverb 31 Section Four - Other Functions Expression Pedal Footswitch Assign LFOs 32 Wah Min/Max Expression Update Factory Reset Expression Pedal Calibration 33 Preset Level Bypass Looper Page 35 Tuner USB Setup Page 37 Section Five - RP1000 Effects Descriptions Wahs Compressors Noise Gates 38 EQ Chorus Stompbox Models Flanger 39 Phasers Pitch 40 Vibrato / Rotary Tremolo 41 Envelope / Special Delays 42 Reverbs Distortions Page 44 Amps Page Page Page 48 Cabinets Page 50 Section Six - Appendix Specications 51 Tone Library Effects Library