Manuals / Edimax Technology / Computer Equipment / Network Router

Edimax Technology Edimax user guide Router Rear Panel, Default Settings, TFTP Download, LAN Ports

Models: Edimax user guide Router

1 81

Download 81 pages 335 b

Page 10

Rear Panel

Rear Panel

	Figure 1-2: Rear Panel

DC 5V	Connect the supplied power adapter here.

WAN 2	Connect the 2nd Broadband Modem here, if available.
Reset Button	When pressed and released, The Load Balancer will reboot (restart) within 1
	second. It resets to default over 3 seconds.
LAN Ports	Connect the PCs to these ports. Both 10BaseT and 100BaseT connections can
	be used simultaneously.
	Note:
	Any port will automatically operate as an "Uplink" port if required. Just use a
	normal LAN cable to connect to a normal port on another hub.
WAN 1	Connect the primary Broadband Modem here.

Default Settings

When The Load Balancer has finished booting, all configuration settings will be set to the factory defaults, including:

•IP Address set to its default value of 192.168.1.1, with a Network Mask of 255.255.255.0

•DHCP Server is enabled

•User Name: admin

•Password cleared (no password)

TFTP Download

This setting should be used only if your Load Balancer is unusable, and you wish to restore it by downloading new firmware. Follow this procedure:

1.Power On The Load Balancer.

2.Use the supplied Windows utility or a TFTP client program applies the new firmware. If using the supplied Windows TFTP program, the screen will look like the following example.

Page 6

Image 10

Edimax Technology Edimax user guide Router manual Rear Panel, Default Settings, TFTP Download, Reset Button, LAN Ports

Contents

Load Balancing Router User’s Guide Page 5 SECURITY MANAGEMENT ……………………………………………………………………………..44 6 QOS CONFIGURATION ………………………………………………………………………………….508 ADVANCED LAN CONFIGURATION ………………………………………………………………...59 System Filter Exception………………………………………………………………………….……Internet Access TCP/IP SettingsGeneral Problems Operation1 Introduction Internet FeaturesShared Broadband Internet Access High-Performance Dual Modem SupportSpecial Applications Access FilterMultiple IP Address Support Virtual ServersEasy Setup Other Features4-Port Switching Hub Password - protected ConfigurationPhysical Details Package ContentsPower Front PanelLED Action ConditionDHCP Server is enabled User Name admin Default SettingsReset Button Rear PanelFigure 1-3 Windows TFTP utility 1 Configuring The Load Balancer for your LAN 2 Basic SetupProcedure OverviewNo Response ? Figure 2-2 Home Screen Admin PasswordIP Address Settings - LAN & DHCPConfiguration Subnet MaskDHCP IP Address Default GatewayLAN Any IP Setup Range2. Installing The Load Balancer in your LAN Figure 2-4 Installation Diagram3. Configuring The Load Balancer for Internet Access Figure 2-5 Primary Setup ScreenMode Settings - Primary SetupConnection TypeOptional Internet Access 4 Configure PCs on your LANTCP/IP Settings 1. Select Start Menu - Settings - Control Panel - Internet OptionsLinux Clients Accessing AOLMacintosh Clients Fixed IP AddressTo act as a DHCP Client recommended 2. Select Control Panel - NetworkOverview 3 Advanced Port SetupPort Options Figure 3-1 Port OptionsTransparent Bridge Settings - Port OptionsConnection Options OptionLoad Balance Figure 3-2 Load BalanceStatistics Settings - Load BalanceLoad Balance InterfaceWAN Port Settings - Advanced PPPoEAdvanced PPPoE PPPoE SessionWAN Port Settings - Advanced PPTPAdvanced PPTP WAN IP AccountHost IP Setup 4 Advanced ConfigurationOverview Settings - Host IP Setup Host Network IdentityBinding Select WAN Port/Select PPPoE session - If the setting above is EnableHost Network Host & GroupConnecting to the Virtual Servers Virtual ServersServer Type Settings - Virtual ServerEnable LAN IPSelect Custom Server Settings - Custom Virtual ServersCustom Virtual Servers Server ListButtons Custom Virtual ServerList in the Special Application Configuration section Settings - Special ApplicationsJust enter your data in the Special Application Configuration Special Application ConfigurationIncoming Protocol Using a Special Application on your PCOutgoing Port Range Incoming Port RangeTo use the Dynamic DNS feature Dynamic DNSSettings Settings - Dynamic DNSService Dynamic DNSMulti DMZ Figure 4-7 Multi DMZFor Static IP Settings - Multi DMZAccess Group Public IP addressFigure 4-8 UPnP Settings - UPnPUPnP UPnP OptionFigure 4-9 NAT NAT Alias Settings - NATConfiguration Advanced Features Figure 4-10 Advanced FeaturesRemote Settings - Advanced FeaturesAccess ExternalProtocol Using Remote Web-based SetupSMTP Simple Mail Transport Protocol Binding Protocol and Port BindingOverview 5 Security ManagementURL Filter Figure 5-1 URL FilterAccess Group Settings - URL FilterBlock Internet AccessFigure 5-2 Access Filter Access FilterSettings - Access Filter Setup Access GroupUser-defined Ports to Block Well-knownports BlockSession Limit Session LimitFigure 5-3 Session Limit Sampling TimeFirewall Exception System Filter ExceptionFigure 5-4 System Filter Exception Foreign Port RangeData - QoS Setup 6 QoS ConfigurationQoS Setup of ServiceData - Policy Configuration Policy ConfigurationNetwork Admission Policy Overview 7 Management AssistantSNMP Figure 7-1 SNMPInformation Settings - SNMPEmail Alert Trap TargetsSettings - Email Alert Enable/Disable Email Alert Email Alert Configuration EventSyslog Figure 7-3SyslogKeep Sent Messages Syslog ConfigurationSyslog Global Syslog ServerFigure 7-4 Admin Password Screen Admin Password ScreenFigure 7-5 Password Dialog Upgrade Firmware Figure 7-6 Firmware Upgrade ScreenRouting 8 Advanced LAN ConfigurationExisting DHCP Server OverviewRouting Settings - RoutingDynamic Entry IndexFor The Load Balancer Gateways Routing Table Configuring Other Routers on your LANStatic Routing - Example GatewayFor Router Bs Default Route For Router As Default RouteEntry 2 Segment System Status 9 Operation and StatusOperation Figure 9-1 System StatusInformation Data - System StatusDevice InformationFigure 9-2 Restore Factory Defaults Restore Factory DefaultsButtons Statistics WAN StatusData - System Status InterfaceData - NAT Status NAT TimeoutsNAT Status LAN IP InfoNAT Traffic ErrorsTCP Prosperity NAT ConnectionsFCC Statement SpecificationsAppendix A CE Marking WarningChecking TCP/IP Settings - Windows 9x/ME Windows TCP/IP SetupOverview TCP/IP Settings Appendix BFigure B-2 IP Address Win Using DHCPUsing Specify an IP Address Figure B-3 Gateway Tab Win 95/98Checking TCP/IP Settings - Windows 1. Select Control Panel - Network and Dial-up ConnectionUsing DHCP Using a fixed IP Address Use the following IP AddressFigure B-6 TCP/IP Properties Win Checking TCP/IP Settings - Windows XP Figure B-7 Network Configuration Windows XPUsing a fixed IP Address Use the following IP Address Using DHCPFigure B-8 TCP/IP Properties Windows XP Internet Access TroubleshootingGeneral Problems ProblemSolution