Manuals / Eiki/Elf / Computer Equipment / Projector

Eiki/Elf EIP-4500 setup guide Setting up the Projector Network Environment

Models: EIP-4500

1 54

Download 54 pages 24.28 Kb

Page 20

Image 20

Confirm or change an IP address for the setup computer.

Setting up the Projector Network Environment

5 Click “Internet Protocol (TCP/IP)”, and click the “Properties” button.

Confirm or change an IP address for the setup computer.

1Confirm and note the current IP address, Subnet mask and Default gateway.

Make sure to note the current IP address, Subnet mask and Default gateway as you will be required to re- set them later.

2The factory default setting for the pro- jector IP address is “192.168.150.2”, Subnet mask is “255.255.255.0” and Default gateway is “0.0.0.0”.

Set temporarily as follows : IP address : 192.168.150.3 Subnet mask : 255.255.255.0 Default gateway : (Do not input any values.)

After setting, click the “OK” but- ton, and then restart the com- puter.

After confirming or setting, proceed to “3. Setting up Network Connection for the Projector”.

Page 20

Image 20

Eiki/Elf EIP-4500 Setting up the Projector Network Environment, Confirm or change an IP address for the setup computer

Contents

SETUP GUIDE Connecting Pin AssignmentsRS-232C Specifications and Commands DimensionsSetting up the Screen Standard Setup Front ProjectionSide View Top ViewScreen Size and Projection Distance Throw DistanceThe graph below is for 100 inches 254 cm screen with 43 normal mode ScreenStandard Zoom Lens Standard equipment with EIP-4500 Screen Size and Projection DistanceThere may be an error of ± 3% in the above values NORMAL ModeFixed Wide Lens AH-45201 There may be an error of ± 3% in the above valuesScreen Size and Projection Distance NORMAL ModeWide-zoom Lens AH-45301 There may be an error of ± 3% in the above valuesScreen Size and Projection Distance NORMAL ModeTele-zoom Lens AH-45501 There may be an error of ± 3% in the above valuesScreen Size and Projection Distance NORMAL ModeTele-zoom Lens AH-45601 There may be an error of ± 3% in the above valuesScreen Size and Projection Distance NORMAL ModeTele-zoom Lens AH-45701 There may be an error of ± 3% in the above valuesScreen Size and Projection Distance NORMAL ModeConnecting Pin Assignments RS-232C Cable Recommended Connection 9-pin D-sub female connectorConnecting Pin Assignments DVI digital Terminal INPUTRS-232C Specifications and Commands Computer controlCommunication conditions Basic formatCommands RS-232C Specifications and CommandsExample When turning on the projector, make the following setting P O W RRS-232C Specifications and Commands RS-232C Specifications and Commands RS-232C Specifications and Commands If an underbar appears in the parameter column, enter a spaceSetting up the Projector Network Environment 1. Connecting the projector to a computer2. Setting an IP address for the computer 3. Setting up a network connection for the projector1. Connecting the Pro- jector to a Computer Setting up the Projector Network Environment2. Setting an IP Address for the Computer Setting up the Projector Network EnvironmentSetting up the Projector Network Environment Confirm or change an IP address for the setup computer3. Setting up a Network Connection for the Projector Setting up the Projector Network EnvironmentSetting up the Projector Network Environment 5 Click the “Apply” buttonVersion 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Confirming the Projector Controlling the ProjectorControlling the Projector via LAN Status StatusSetting and Adjusting the Setting the SecurityProjector Settings & Adjustments Network - SecurityMaking General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail - Originator Settings GeneralLamp, Temp Mail - Recipient SettingsControlling the Projector via LAN SETUP MENU Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C When Connecting Using Telnet Setting the Projector Using RS-232C or TelnetSETUP MENU Main Menu ADVANCED SETUP MENUSetting the Projector Using RS-232C or Telnet SETUP MENUControlling the Projector Using RS-232C or Telnet View Setting Detail ListVView All Setting Set ItemsSave Settings and Quit Controlling the Projector Using RS-232C or TelnetQuit without Saving Set SSave & QuitIP Address Setting Default Gateway SettingSubnet Mask Setting 3Default GatewayUser Name Setting Password SettingProjector Name Setting 5PasswordDisconnecting All Connec Setting Auto Logout TimeEntering ADVANCED SETUP MENU Data Port SettingSetting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses ADVANCED5Network Ping TestSetting of Search Port Return to Default SettingsADVANCED!Restore Default Setting Return to Main MenuStack Projection InfoSetting up the Stack Projection Stack ProjectionBasic MasterApplication Stack ProjectionVideo Wall Projection InfoSetting up the Video Wall Projection Basic Video Wall ProjectionINPUT 1 terminal INPUT 1 terminal1 Access one of the four projectors via Internet Explorer Video Wall Projection2 Click “Video Wall” on the menu 3 Select “2 X 2” on “Division”Adjusting the Position Horizontally and Vertically Returning to the Default Video Wall SetupAssigning the Projected Image on the Video Wall Setup Front ProjectionNotes on the Wide Video Wall Projection Video Wall ProjectionSetting up the Video Wall Projection Application Video Wall ProjectionPreparation Video Wall ProjectionVideo Wall Projection 4 Turn on all of the projectorsSlave Video Wall ProjectionMaster Troubleshooting Communication cannot be established with the projectorFor network settings for the projector, refer to page Subnet mask Gateway address 0.0.0.0 Not UsedTroubleshooting Usage examples of ipconfigC\ipconfig /? displays how to use “ipconfig.exe”Troubleshooting Side View DimensionsUnits inches mm