Jectors as shown below, Projector 3 Slave | Eiki/Elf EIP-4500

Video Wall Projection

■Preparation

•Follow the procedure below after setting up the basic connection.

•When “User Name” and “Password” have been set to the projector, reset them before the stack projection

setup. To set “User Name” and “Password”, use the same user name and password for both of the master and slave projectors. (See page 25.)

•Set “Data Port” with the same number for both of the master and slave projectors. (See page 26.)

Info

•Do not use network software or equipment while it is accessing the projector via the port of the same number used for the master or slave projector, otherwise you cannot properly control multiple projectors with one remote control.

1 Change the TCP/IP settings for the computer as shown below.

(See “Setting an IP Address for the Computer” on page 19 for the details.)

• IP address	: 192.168.150.2
• Subnet mask	: 255.255.255.0

• Default gateway : (Do not input any values.)

Note

•The TCP/IP settings shown are examples to make connections following the diagram.

•When using other equipment in the same network, be careful about the IP address overlap or other network settings.

•Consult your network administrator for as- sistance with the network settings.

2 Change the TCP/IP settings for			3 Connect the computer and the pro-
each projector as shown below.			3 Connect the computer and the pro-
(See “Setting up a Network Connection for the			jectors as shown below.
Projector” on page 21 for the details.)
• IP address	Projector 1 : 192.168.150.3
	Projector 2	: 192.168.150.4
	Projector 3	: 192.168.150.5
	Projector 4	: 192.168.150.6
• Subnet mask		: 255.255.255.0
• Default gateway		: 0.0.0.0

Projector 1:

Master

Projector 2: Slave

LAN terminal

Computer

LAN cable

LAN terminal

Projector 3: Slave

LAN terminal

Hub

Projector 4: Slave

LAN cable (straight-through type)

LAN terminal

47

Image 47

Eiki/Elf EIP-4500 Change the TCP/IP settings for the computer as shown below, Jectors as shown below, Projector 3 Slave

Contents

Setup Guide Standard Setup Front Projection Setting up the Screen Throw Distance Screen Size and Projection Distance F1.8-F2.0, f=25.6-31.3 mm Standard Zoom Lens Standard equipment with EIP-4500 F2.5, f=11.6 mm Fixed Wide Lens AH-45201 F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-45301 F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45501 F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45601 F2.4-F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-45701 RGB Input Component Input Connecting Pin Assignments Connecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions W R Commands Return Input 5 Tint -30 +30 OK or ERR CLR Temp Connecting the projector to a computer Setting up the Projector Network Environment Turn on the projector Turn on the computer Connecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Control Confirming the ProjectorControlling the Projector Status Status Network Security Setting and AdjustingSetting the Security Projector Settings & Adjustments General Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs Mail Originator Settings Mail Recipient Settings Input PJS11234 and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter key Clickstartfrom theWindows desk- top and select Run When Connecting Using Telnet 4User Name Factory default setting Not Re- quired Setup Menu Main Menu Set Items Controlling the Projector Using RS-232C or TelnetView Setting Detail List VView All Setting Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & Quit Subnet Mask Setting IP Address SettingDefault Gateway Setting RS-232C Baud Rate Set User Name SettingPassword Setting Projector Name Setting Data Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup Menu Accepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Stack Projection Turn off the both projectors Setting up the Stack ProjectionProjector 1 Master Projector 2 Slave Slave Projector MasterProjector Hub Video Wall Projection Setting up the Video Wall Projection Basic Click the assigning button for the desired position Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Select 2 X 2 on Division Select 1 X 1 on Division Click the assigning button Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Assigning the Projected Image on the Video Wall Setup Video Wall Projection Projector Slave Setting up the Video Wall Projection Application Projector 3 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector Master Projector 2 Slave Make the IP address for each pro- jector as shown below Click Stack on the menu Select Master on Stack SettingClick Stack on the menu Select Slave on Stack Setting Repeat the same procedure from the to 12 for the projector 3 When connecting the projector using serial-connection Troubleshooting Troubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions