Manuals / Eiki/Elf / Computer Equipment / Projector

Eiki/Elf EIP-4500 setup guide Connecting the Pro- jector to a Computer

Models: EIP-4500

1 54

Download 54 pages 24.28 Kb

Page 18

Image 18

Setting up the Projector Network Environment

1.Connecting the Pro- jector to a Computer

Establishing a one-to-one connection from the projector to a computer. Using a commercially available LAN cable (UTP cable, Category 5, cross-over type) you can configure the projector via the computer.

1 Disconnect the computer’s LAN cable from the existing network.

A LAN cable being connected to the network

2 Connect a commercially available LAN cable (UTP cable, Category 5, cross-over type) to the projector’s LAN terminal and connect the other end of the cable to the computer’s LAN terminal.

LAN cable

Turn on the projector.

Turn on the computer.

Info

Confirm that the LINK LED on the side of the projector illuminates. If the LINK LED does not illuminate, check the following :

•The LAN cable is properly connected.

•The power switches of both the projector and the computer are on.

This completes the connection. Now proceed to “2. Setting an IP Address for the Com- puter”.

Page 18

Image 18

Eiki/Elf EIP-4500 setup guide Connecting the Pro- jector to a Computer, Setting up the Projector Network Environment

Contents

RS-232C Specifications and Commands SETUP GUIDEConnecting Pin Assignments DimensionsSide View Setting up the ScreenStandard Setup Front Projection Top ViewThe graph below is for 100 inches 254 cm screen with 43 normal mode Screen Size and Projection DistanceThrow Distance ScreenNORMAL Mode Standard Zoom Lens Standard equipment with EIP-4500Screen Size and Projection Distance STRETCH ModeSTRETCH Mode Fixed Wide Lens AH-45201NORMAL Mode There may be an error of ± 3% in the above valuesSTRETCH Mode Wide-zoom Lens AH-45301NORMAL Mode There may be an error of ± 3% in the above valuesSTRETCH Mode Tele-zoom Lens AH-45501NORMAL Mode There may be an error of ± 3% in the above valuesSTRETCH Mode Tele-zoom Lens AH-45601NORMAL Mode There may be an error of ± 3% in the above valuesSTRETCH Mode Tele-zoom Lens AH-45701NORMAL Mode There may be an error of ± 3% in the above valuesConnecting Pin Assignments RS-232C Cable Recommended Connection 9-pin D-sub female connectorConnecting Pin Assignments DVI digital Terminal INPUTCommunication conditions RS-232C Specifications and CommandsComputer control Basic formatExample When turning on the projector, make the following setting CommandsRS-232C Specifications and Commands P O W RRS-232C Specifications and Commands RS-232C Specifications and Commands RS-232C Specifications and Commands If an underbar appears in the parameter column, enter a space2. Setting an IP address for the computer Setting up the Projector Network Environment1. Connecting the projector to a computer 3. Setting up a network connection for the projector1. Connecting the Pro- jector to a Computer Setting up the Projector Network Environment2. Setting an IP Address for the Computer Setting up the Projector Network EnvironmentSetting up the Projector Network Environment Confirm or change an IP address for the setup computer3. Setting up a Network Connection for the Projector Setting up the Projector Network EnvironmentSetting up the Projector Network Environment 5 Click the “Apply” buttonControlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Controlling the Projector via LAN Confirming the ProjectorControlling the Projector Status StatusProjector Settings & Adjustments Setting and Adjusting theSetting the Security Network - SecurityMail - Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs GeneralMail - Recipient Settings Controlling the Projector via LANLamp, Temp Setting the Projector Using RS-232C or Telnet When Connecting Using RS-232CSETUP MENU When Connecting Using Telnet Setting the Projector Using RS-232C or TelnetSetting the Projector Using RS-232C or Telnet SETUP MENU Main MenuADVANCED SETUP MENU SETUP MENUVView All Setting Controlling the Projector Using RS-232C or TelnetView Setting Detail List Set ItemsQuit without Saving Set Save Settings and QuitControlling the Projector Using RS-232C or Telnet SSave & QuitSubnet Mask Setting IP Address SettingDefault Gateway Setting 3Default GatewayProjector Name Setting User Name SettingPassword Setting 5PasswordEntering ADVANCED SETUP MENU Disconnecting All ConnecSetting Auto Logout Time Data Port SettingAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test ADVANCED5Network Ping TestADVANCED!Restore Default Setting Setting of Search PortReturn to Default Settings Return to Main MenuStack Projection InfoBasic Setting up the Stack ProjectionStack Projection MasterApplication Stack ProjectionVideo Wall Projection InfoINPUT 1 terminal Setting up the Video Wall Projection BasicVideo Wall Projection INPUT 1 terminal2 Click “Video Wall” on the menu 1 Access one of the four projectors via Internet ExplorerVideo Wall Projection 3 Select “2 X 2” on “Division”Assigning the Projected Image on the Video Wall Setup Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Front ProjectionNotes on the Wide Video Wall Projection Video Wall ProjectionSetting up the Video Wall Projection Application Video Wall ProjectionPreparation Video Wall ProjectionVideo Wall Projection 4 Turn on all of the projectorsVideo Wall Projection MasterSlave For network settings for the projector, refer to page TroubleshootingCommunication cannot be established with the projector Subnet mask Gateway address 0.0.0.0 Not UsedC\ipconfig /? TroubleshootingUsage examples of ipconfig displays how to use “ipconfig.exe”Troubleshooting Dimensions Units inches mmSide View