Stack Projection | Eiki/Elf EIP-4500 specs

Stack Projection

The stack projection allows you to increase the brightness of an image by stacking two projectors and projecting same image simultaneously.

Info

•To set up the stack projection, assign a projector as the master and the other projector as the slave and connect the projectors with commercially available LAN cables (UTP cable, Category 5, cross-over type). In this way, you can control the both projectors with one remote control.

•The buttons below can control both the master and the slave at one time.

• STANDBY-ON button	• AUTO SYNC button
• BLACK SCREEN button	• RESIZE button
• INPUT 1 - 5 buttons	• PICTURE MODE button
• MUTE button	• BREAK TIMER button
• VOLUME buttons	• FREEZE button

•In normal operation, the projector set as the slave cannot be controlled by the remote control.

Only while the remote control is connected to the projector with a ø3.5 mm minijack cable (commercially available), the projector set as the slave can be controlled by the remote control.

•Even while the projector is set as the slave, the buttons on the projector can be used.

38

Image 38

Eiki/Elf EIP-4500 setup guide Stack Projection

Contents

Setup Guide Setting up the Screen Standard Setup Front Projection Screen Size and Projection Distance Throw Distance Standard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mm Fixed Wide Lens AH-45201 F2.5, f=11.6 mm Wide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mm Tele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mm Connecting Pin Assignments RGB Input Component Input Connecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions Commands W R Return Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computer Connecting the Pro- jector to a Computer Turn on the projector Turn on the computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Status Status Confirming the ProjectorControlling the Projector Control Projector Settings & Adjustments Setting and AdjustingSetting the Security Network Security Mail Originator Settings Making General Settings for the Network NetworkSetting for Sending E-mail when an Error Occurs General Mail Recipient Settings Input setup and press the Enter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input PJS11234 and press the Enter key When Connecting Using Telnet Clickstartfrom theWindows desk- top and select Run Setup Menu Main Menu 4User Name Factory default setting Not Re- quired VView All Setting Controlling the Projector Using RS-232C or TelnetView Setting Detail List Set Items SSave & Quit Save Settings and QuitQuit without Saving Set Tings QQuit Unchanged Subnet Mask Setting IP Address SettingDefault Gateway Setting Projector Name Setting User Name SettingPassword Setting RS-232C Baud Rate Set Entering Advanced Setup Menu Disconnecting All ConnecSetting Auto Logout Time Data Port Setting Accepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Stack Projection Projector 2 Slave Setting up the Stack ProjectionProjector 1 Master Turn off the both projectors Slave Projector MasterProjector Video Wall Projection Hub Setting up the Video Wall Projection Basic Select 2 X 2 on Division Access one of the four projectors via Internet ExplorerClick Video Wall on the menu Click the assigning button for the desired position Assigning the Projected Image on the Video Wall Setup Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Select 1 X 1 on Division Click the assigning button Video Wall Projection Setting up the Video Wall Projection Application Projector Slave Projector Master Projector 2 Slave Change the TCP/IP settings for the computer as shown belowJectors as shown below Projector 3 Slave Make the IP address for each pro- jector as shown below Click Stack on the menu Select Master on Stack SettingClick Stack on the menu Select Slave on Stack Setting Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connection Troubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm