Video Wall Projection, Hub | Eiki/Elf EIP-4500 instruction

Video Wall Projection

Usually, a costly image-processing device is required to set up a video wall projection. This projector has built-in video wall capability that doesn’t require additional equipment.

Hub

Info

•Before setting up the video wall projection, install Internet Explorer (version 5.0 or later).

•Video wall is not compatible with resolutions higher than SXGA.

•Image quality may deteriorate when picture signals are input through multiple projectors with an RGB cable or an RCA cable in a daisy chain connection.

41

Image 41

Eiki/Elf EIP-4500 setup guide Video Wall Projection, Hub

Contents

Setup Guide Standard Setup Front Projection Setting up the Screen Throw Distance Screen Size and Projection Distance F1.8-F2.0, f=25.6-31.3 mm Standard Zoom Lens Standard equipment with EIP-4500 F2.5, f=11.6 mm Fixed Wide Lens AH-45201 F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-45301 F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45501 F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45601 F2.4-F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-45701 RGB Input Component Input Connecting Pin Assignments Connecting Pin Assignments Basic format RS-232C Specifications and CommandsComputer control Communication conditions W R Commands Return Input 5 Tint -30 +30 OK or ERR CLR Temp Connecting the projector to a computer Setting up the Projector Network Environment Turn on the projector Turn on the computer Connecting the Pro- jector to a Computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Version 5.0 or later Controlling the Projector Using Internet ExplorerControlling the Projector via LAN Controlling the Projector Confirming the ProjectorStatus Status Control Setting the Security Setting and AdjustingProjector Settings & Adjustments Network Security Setting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Originator Settings General Mail Recipient Settings When Connecting Using RS-232C Setting the Projector Using RS-232C or TelnetInput setup and press the Enter key Input PJS11234 and press the Enter key Clickstartfrom theWindows desk- top and select Run When Connecting Using Telnet 4User Name Factory default setting Not Re- quired Setup Menu Main Menu View Setting Detail List Controlling the Projector Using RS-232C or TelnetVView All Setting Set Items Quit without Saving Set Save Settings and QuitSSave & Quit Tings QQuit Unchanged Subnet Mask Setting IP Address SettingDefault Gateway Setting Password Setting User Name SettingProjector Name Setting RS-232C Baud Rate Set Setting Auto Logout Time Disconnecting All ConnecEntering Advanced Setup Menu Data Port Setting Accepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Stack Projection Projector 1 Master Setting up the Stack ProjectionProjector 2 Slave Turn off the both projectors Slave Projector MasterProjector Hub Video Wall Projection Setting up the Video Wall Projection Basic Click Video Wall on the menu Access one of the four projectors via Internet ExplorerSelect 2 X 2 on Division Click the assigning button for the desired position Returning to the Default Video Wall Setup Adjusting the Position Horizontally and VerticallyAssigning the Projected Image on the Video Wall Setup Select 1 X 1 on Division Click the assigning button Video Wall Projection Projector Slave Setting up the Video Wall Projection Application Jectors as shown below Change the TCP/IP settings for the computer as shown belowProjector Master Projector 2 Slave Projector 3 Slave Make the IP address for each pro- jector as shown below Click Stack on the menu Select Master on Stack SettingClick Stack on the menu Select Slave on Stack Setting Repeat the same procedure from the to 12 for the projector 3 When connecting the projector using serial-connection Troubleshooting Troubleshooting \ After the initialization, carry out setting again Units inches mm Dimensions