Confirming the Projector, Status Status | Eiki/Elf EIP-4500 guide

Controlling the Projector via LAN

Confirming the Projector

Status (Status)

Controlling the Projector

(Control)

On this screen, you can confirm the projector status. You can confirm the following items :

•MAC Address

•Power

•Condition

•Lamp Timer 1

•Lamp Timer 2

•Lamp Life 1

•Lamp Life 2

•Input

•Signal Info

Note

•If you click the “Refresh” button before the screen is displayed completely, an error message (“Server Busy Error”) will be dis- played. Wait for a moment and then oper- ate again.

•For details about each item, refer to the owner’s manual of the projector.

On this screen, you can perform projector con- trol. You can control the following items :

•Power

•Input Select

•Volume

•Mute (Audio) [OFF] [ON]

•Black Screen [OFF] [ON]

Note

•If you click the “Refresh” button before the screen is displayed completely, an error mes- sage (“Server Busy Error”) will be displayed. Wait for a moment and then operate again.

•You cannot operate this page while the pro- jector is warming up.

•While the projector is in standby mode, you can only control “Power ON”.

•For details about each item, refer to the owner’s manual of the projector.

24

Image 24

Eiki/Elf EIP-4500 setup guide Confirming the Projector, Controlling the Projector, Status Status

Contents

Setup Guide Setting up the Screen Standard Setup Front Projection Screen Size and Projection Distance Throw Distance Standard Zoom Lens Standard equipment with EIP-4500 F1.8-F2.0, f=25.6-31.3 mm Fixed Wide Lens AH-45201 F2.5, f=11.6 mm Wide-zoom Lens AH-45301 F2.5, f=21.2-25.8 mm Tele-zoom Lens AH-45501 F2.4-F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-45601 F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-45701 F2.4-F2.5, f=62.1-97.8 mm Connecting Pin Assignments RGB Input Component Input Connecting Pin Assignments RS-232C Specifications and Commands Computer control Communication conditionsBasic format Commands W R Return Input 5 Tint -30 +30 OK or ERR CLR Temp Setting up the Projector Network Environment Connecting the projector to a computer Connecting the Pro- jector to a Computer Turn on the projector Turn on the computer Setting an IP Address for the Computer Confirm or change an IP address for the setup computer Setting up a Network Connection for the Projector After setting items, wait for 10 seconds and then re-access Controlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Confirming the Projector Controlling the ProjectorStatus Status Control Setting and Adjusting Setting the SecurityProjector Settings & Adjustments Network Security Making General Settings for the Network Network Setting for Sending E-mail when an Error OccursMail Originator Settings General Mail Recipient Settings Setting the Projector Using RS-232C or Telnet When Connecting Using RS-232CInput setup and press the Enter key Input PJS11234 and press the Enter key When Connecting Using Telnet Clickstartfrom theWindows desk- top and select Run Setup Menu Main Menu 4User Name Factory default setting Not Re- quired Controlling the Projector Using RS-232C or Telnet View Setting Detail ListVView All Setting Set Items Save Settings and Quit Quit without Saving SetSSave & Quit Tings QQuit Unchanged IP Address Setting Default Gateway SettingSubnet Mask Setting User Name Setting Password SettingProjector Name Setting RS-232C Baud Rate Set Disconnecting All Connec Setting Auto Logout TimeEntering Advanced Setup Menu Data Port Setting Setting of Accept IP Ad- dress Carrying out Network Ping TestAccepting All IP Addresses Setting of Search Port Return to Default SettingsReturn to Main Menu Stack Projection Setting up the Stack Projection Projector 1 MasterProjector 2 Slave Turn off the both projectors Projector Master ProjectorSlave Video Wall Projection Hub Setting up the Video Wall Projection Basic Access one of the four projectors via Internet Explorer Click Video Wall on the menuSelect 2 X 2 on Division Click the assigning button for the desired position Adjusting the Position Horizontally and Vertically Returning to the Default Video Wall SetupAssigning the Projected Image on the Video Wall Setup Select 1 X 1 on Division Click the assigning button Video Wall Projection Setting up the Video Wall Projection Application Projector Slave Change the TCP/IP settings for the computer as shown below Jectors as shown belowProjector Master Projector 2 Slave Projector 3 Slave Click Stack on the menu Select Master on Stack Setting Click Stack on the menu Select Slave on Stack SettingMake the IP address for each pro- jector as shown below Repeat the same procedure from the to 12 for the projector 3 Troubleshooting When connecting the projector using serial-connection Troubleshooting \ After the initialization, carry out setting again Dimensions Units inches mm