Belt Cover Right Screw, Right Bolt Left Bolt | Electrolux OHV

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.32 Replace Auger Belt

1)Remove spark plug wire from plug.

2)Remove Chute Assy. See section 7.51

3)Remove both 3/8" screws that secure belt cover. Remove belt cover.

BELT COVER

RIGHT SCREW

4)Place a chair or saw horse under handle for support after auger section is split.

7)Place new belt on auger pulley.

8)Lift auger housing into position and ensure that slotted bracket on auger housing are placed onto the rod at base of powerhead

SLOTTED

BRACKET

ROD

RIGHT BOLT

LEFT BOLT

5)Remove both 9/16" hex bolts that hold the powerhead and auger housing together.

6)Remove belt from drive pulley as you separate the auger from the powerhead assembly

AUGER BELT

IDLER PULLEY

9)Route auger belt around pulleys, checking that the belt does not catch on idler brkt.

10)Reinstall bolts to secure auger housing to the powerhead.

11)Reinstall the belt cover and the chute assembly. ( See Section 7.51)

36

www.mymowerparts.com

Image 36

Electrolux OHV service manual Belt Cover Right Screw, Right Bolt Left Bolt, Idler Pulley

Contents

For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation Training Maintenance and Storage Operation Specifications Consumer Assembly Parts Packed Separately in Carton Consumer Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs See Fig Install Chute Deflector Remote Control See Figs Install Weight BAG See FigCheck Tire Pressure Consumer Operation Know Your Snow Thrower Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the en HOW to USE Your Snow Thrower Stopping Power Steering Operation See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine Check Engine OIL Level See FigADD Gasoline See Fig To Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Consumer Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Consumer Service and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Other CarburetorEngine OIL Cylinder Troubleshooting Belt Guide 16 to 1/8Clearance Auger Belt Traction Belt Idler Spring Adjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler Gauge Speed Control Assembly Adjustment 2nd Reverse PositionNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD Lever Feeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Traction Auger Engagement Lever Screws Interlock Spring Check Wear HereConsole Lock TAB Into Hole Backside View Section Spring Cable Assembly Rotator Head Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever Screws Speed Control Assembly Retainer SpringsNUT Washer PIN Snow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link Retainer Snow Thrower Section Chassis / Engine / Pulleys Belt Cover Right Screw Right Bolt Left BoltIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt Spring Barrel Connector Wood Support Housing ScrewFrame Slot For Drive Plate Drive Spring Belt Guide Drive Belt Snow Thrower Section Drive HEX Head Screws NUT HEX ShaftScrews Flange Bearing Flange Bearing Pinion Gear Long HEX Shaft Drive Plate Assembly Screws NutsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing Screws To Reinstall Cable Assembly Locknut Snow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear Bolts For Husqvarna Parts Call 606-678-9623 or Impeller Shaft Tecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no Description Service Notes Part Number 184962 printed for MY