Drive Plate Slot Idler Spring Left Wheel | Electrolux OHV specification

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.33 Belt Guide Dimension.

BELT GUIDE

1/16" to 1/8"

CLEARANCE AUGER BELT

7.34 Replace Traction Drive Belt

7.35 Replace Traction Drive Pulley

1)Separate powerhead assembly from auger housing assembly (see section 7.61)

1)Separate auger assembly from Powerhead assembly (See section 7.61)

DRIVE PLATE

SLOT

IDLER SPRING

LEFT WHEEL

2)Ensure that idler spring is in place before re-assembly. Put tape over the spring hook on the outside of housing to keep the spring in proper position.

3)Use a 3/8" ratchet with 6" extension inserted in square opening on the idler arm to release the tension on the belt. Pull on ratchet to rotate idler arm.

4)Remove defective belt and replace with new traction drive belt.

NOTE: Idlers, Idler Brackets, and Springs for both drive Belts are now accessable.

5)Re-attach auger housing to powerhead (see

section 7.61 or section 7.32)	37

2)Remove Traction Drive Belt ( Section 7.33 ) from engine pulley.

3)Use traction drive belt to prevent drive pulley from turning remove 1⁄2” hex head bolt holding the pulley in place

4)Use antiseize compound before replacing Pulley and reinstall washer, bolt at 15-20 Ft.Lbs., and belt.

5)Reassemble auger housing to powerhead assembly.

7.36 Idler Spring locations

TRACTION BELT SPRING

AUGER BELT SPRING

www.mymowerparts.com

Image 37

Electrolux OHV service manual Drive Plate Slot Idler Spring Left Wheel, Traction Belt Spring Auger Belt Spring

Contents

For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training Preparation Operation Maintenance and Storage Specifications Consumer Assembly Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Consumer Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle See Fig Install Auger Control ROD See Figs Install Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower Consumer Operation Recoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Adjust Skid Plates See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Check Engine OIL Level See Fig Before Starting the EngineADD Gasoline See Fig To Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen General Recommendations Consumer MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Consumer Service and AdjustmentsChute Deflector To Remove Wheels See Fig Carburetor OtherEngine OIL Cylinder Troubleshooting 16 to 1/8 Belt GuideClearance Auger Belt Traction Belt Idler Spring Protective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control Rod 2nd Reverse Position Speed Control Assembly AdjustmentNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD Lever Feeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Interlock Spring Check Wear Here Traction Auger Engagement Lever ScrewsConsole Lock TAB Into Hole Backside View Section Cable Assembly Rotator Head Spring Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever Screws Retainer Springs Speed Control AssemblyNUT Washer PIN Snow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering Clutch Snow Thrower Section Chassis / Engine / Pulleys Right Bolt Left Bolt Belt Cover Right ScrewIdler Pulley Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left Wheel Housing Screw Barrel Connector Wood SupportFrame Slot For Drive Plate Drive Spring Belt Guide Drive Belt Snow Thrower Section Drive NUT HEX Shaft HEX Head ScrewsScrews Flange Bearing Flange Bearing Pinion Gear Long HEX Shaft Nuts Drive Plate Assembly ScrewsFrame Slot Lubricate HEX Shaft Axle Bearing Screws Instruction Cable Assembly Locknut To Reinstall Snow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shaft For Husqvarna Parts Call 606-678-9623 or Tecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE Engine Service Notes Part Number 184962 printed for MY