Connecting To Gas | Electrolux SIG 556 specs

4. CONNECTING TO GAS

4. CONNECTING TO GAS

This appliance is designed to be installed with an appliance flexible connection only. Supply piping should not be less that R³/8. Connection is made to the Rc ½ (½" B.S.P.) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE:

ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED TO SHUT OFF VALVE I.E.: DO NOT USE P.T.F.E. SEALANT TAPE. Check for gas soundness after connecting to the gas supply.

The gas bayonet connector must be fitted in the shaded area indicated in Fig.3. Take into account that it must be possible to pull the appliance forward sufficiently. The hose must not get caught on the stability bracket.

IMPORTANT: FLEXIBLE TUBING USED MUST COMPLY WITH BS. 669 CURRENT EDITION.

L.P.G. FLEXIBLE CONNECTIONS MUST BE OF A TYPE SUITABLE FOR L.P.G. AND CAPABLE OF OPERATION UP TO 50 mbar AND TO CARRY A RED STRIPE, BAND OR LABEL.

50 100

Fig.3

850	700
250	450
All dimensions in mm

5. CONNECTION TO THE ELECTRICITY SUPPLY

WARNING: THIS APPLIANCE MUST BE EARTHED.	Fig.4
DO NOT EARTH THIS APPLIANCE TO THE GAS
SUPPLY PIPING.
This appliance must be connected to 230V-240V A.C.
50Hz supply. It is supplied with 2 metres of 5 amp 3 core
cable incorporating a moulded 13 amp plug , fitted with a
3 amp fuse, which can be plugged directly into the
nearest suitable socket. Ensure the plug is accessible to
the user. If this is not long enough, the supply cable can
be replaced totally by a longer cable at least 0.75mm²
nominal cross sectional area (24/0.2mm).

IF THE MOULDED PLUG IS CUT FROM THE CABLE

FOR ANY REASON, IT MUST BE DESTROYED OR

DISPOSED OF SAFELY, AS THE PROTRUDING

WIRES WILL BE AN ELECTRIC SHOCK HAZARD.

If any other type of plug is used it should incorporate a 3

amp fuse in either the plug or adapter or at the distribution board.

If the cable has to be threaded through small apertures in cabinets etc., it may be disconnected from the appliance, then re-connected to as shown in Fig.4.

DO NOT EXTEND THE CABLE USING PLASTIC OR CERAMIC CONNECTION TERMINAL BLOCKS AND/OR INSULATION TAPE.

ALL EXTERNAL WIRING BETWEEN THE APPLIANCE AND THE ELECTRICAL SUPPLY SHALL COMPLY WITH I.E.E. WIRING REGULATIONS.

48

Image 48

Electrolux SIG 556 installation instructions Connecting To Gas, Connection To The Electricity Supply

Contents

Operating and Installation Instructions For your safety IntroductionS I G 5 5 RATING PLATE Contents Contents Lighting the appliance HotplateLighting the appliance To light Grill/second oven GrillSecond oven Main oven To turn off any burnerOven light Prior to using the grill The grillHeat control The grill Cooking positions GeneralPreheating Positioning food on the grid The grill pan and handle The hotplate Burner sizesThe hotplate Take care to avoid burns and scalds when you Helpful hints the flames lick round the sides of thequickly and there will be less steam in This way they will cook more quickly The ovens Heat zonesOven shelves The ovens Baking trays and dishes Roasting Condensation Oven cooking chart - Main oven Oven cooking chart Turkey below 4.5kg 10lbs Bread 0.45 kg 1lb loaves 0.90 kg 2 lb loaves Oven cooking chart - Second oven 3½ - 4½ hours on a metal plate, or if plates are flat andTo help pastry brown on the underside cook have no rim underneath, place on baking S I G The electronic timer To use the TimerThe electronic timer To set the time of day Setting the controls for automatic use Automatic control shows in the display. The Hints and tips for automatic cooking Slow cooking Food preparation - slow cookingSlow cooking S I G 5 5 Soups, casseroles and stews VegetablesMilk puddings General points for slow cooking Frozen foods Care and cleaning For your safety Cleaning the handles and control knobsCare and cleaning When replacing hotplate burner parts The hotplate The grill The grill and oven furniture The ovens Main oven cleaning cycle least 30 minutes Top oven cleaning cycle MARKMARK Cleaning between the outer and inner door glass To remove the outer glass Cleaning The Door Glass Installing the applianceInstallation Location Appliance dimensions Positioning General information For your safety Connecting to the electricity supplyMoving your appliance General information Replacing the oven light bulb What is wrong and why? What is wrong and why?Problem Check S I G 5 5 Problem Having difficulty cleaning any part of the applianceThe oven light will not work Service and spare parts Servicing0 8 7 0 5 9 2 9 9 Customer Care Department The Gas Consumers Council INSTALLATION INSTRUCTIONS Serial number on front frame. Rating Plate on top rear of panel TECHNICAL DATA DIMENSIONSCONNECTIONS GRILL IMPORTANT - SAFETY REQUIREMENTS MAIN OVENSECOND OVEN GENERAL All dimensions in mm LOCATION OF APPLIANCE100 less than 400 Fig.1a INSTALLATION 1. PARTS REQUIRED2. LEVELLING THE APPLIANCE 3. FITTING THE STABILITY BRACKET 4. CONNECTING TO GAS 5. CONNECTION TO THE ELECTRICITY SUPPLY 6. PRESSURE TESTING 7. CHECKING THE GRILL8. CHECKING THE HOTPLATE 9. CHECKING LID SHUT-OFF DEVICE 10. CHECKING THE MAIN OVEN CONTROLS 11. CHECKING THE MAIN OVEN12. AUTOMATIC OPERATION TO SET THE TIME OF DAY see Fig.5 13. CHECKING THE SECOND OVEN 14. CHECKING THE MAIN OVEN LIGHTGENERAL NOTE N O T E S N O T E S SIG 556 Contents Check List IMPORTANT NOTICE PARKINSON COWAN 55 - 77 HIGH STREET SLOUGH BERKSHIRE SL1 1DZTELEPHONE 0870 5 Part Number311625804