Manuals / Emerson / Computer Equipment / Computer Hardware

Emerson MVME147 manual Open Packet, Scsi Packets

Models: MVME147

1 170

Download 170 pages 32.5 Kb

Page 146

Open Packet

7

SCSI PACKETS

$02	xxxxxxxx		Status from SCSI
			firmware (byte 0)
			(Note 1)
$03	xxxxxxxx		Status from SCSI
			firmware (byte 1)
			(Note 1)
$04	00000000	00000000	Reserved
$06	00000000	00000000	Reserved
$08	00000000	00000000	Reserved
$0A	00000000	00000000	Reserved
$0C	00000000	00000000	Reserved
$0E	00000000	00000000	Reserved
$10	00000000	00000000	Reserved
$12	00000000	00000000	Reserved
$14	00000000		Reserved
$15	00101100		SCSI function ($60 =
			erase
$16	000000xx		Interrupt level (7
			through 0) (0 = polled
			mode)
$17	xxxxxxxx		Vector number to use
			upon return
$18	xxxxxxxx		Status from SCSI
			firmware (byte 2)
			(Note 1)
$19	xxxxxxxx		Status from SCSI
			firmware (byte 3)
			(Note 1)
NOTE:		1.	Refer to Chapter 3.

Open Packet

The open packet is a read of the first blocks of a device. This command is intended as a "safe" read that won’t overrun the byte count when the block size of the device is unknown.

7-66

Image 146

Emerson MVME147 manual Open Packet, Scsi Packets

Contents

Introduction FeaturesGENERAL INFORMATION Modes of OperationMVME147 SCSI Firmware Entry Points The SCSI firmware initializes these vectors Equipment Supported CONTROLLE DEVICE CONTROLLECONTROLLE PARTDEVICE Devices Supported Under Common Command SetCONTROLLE PARTDOCUMENT TITLE Related DocumentationMOTOROLA PUBLICATION NUMBERManual Terminology MOTOROLAGENERAL INFORMATION Introduction CUSTOM SCSI PACKETSInitiator Role Custom Packet CUSTOM SCSI PACKETS Initiator Role Custom Packet NOTES PHASE CODE PHASEInitiator Role Custom Packet +$00 +$68 status Note ASYNC the firmware status xxxxxxxx xxxxxxxx Page CUSTOM SCSI PACKETS Initiator Role Custom Packet CUSTOM SCSI PACKETS TARGET Enable Custom Packet TARGET Enable Custom PacketNOTES Status from SCSITARGET Enable Custom Packet TARGET Sequence Custom Packet TARGET Sequence Custom Packet CUSTOM SCSI PACKETS NOTESTARGET Sequence Custom Packet WORDS $04 and $06 CUSTOM SCSI PACKETS TARGET Sequence Custom Packet CUSTOM SCSI PACKETS TARGET Sequence Custom Packet RETRY COUNT. Not used by the TARGET role firmwareCUSTOM SCSI PACKETS Control Flags PACKET RETURN STATUSPacket Return Status SCSI The command was retried retry count times Bit 3 FM Filemark Bit 4 COMMAND RETRY1 = Retries were performed Bit 5 COMMAND RE Packet Return Status Bit 2 EOM End of mediaPACKET RETURN STATUS Codes Table 3-1.Packet Status CodesIntermediate Return CODECODE Final Return CodesTable 3-1.Packet Status Codes Intermediate ReturnCODE Table 3-2.Packet Status Codes cont’dSCSI Bus Reset Packet section in Chapter MEANINGController-Dependent Request-Sense-Data Error-Class7 CodesTable 3-3.Packet Status Codes cont’d CODECODE SCSI Status Returned in Status PhaseTable 3-4.Packet Status Codes cont’d MEANINGCODE Request-Sense-Data Error-Class0 through 6 CodesTable 3-5.Packet Status Codes cont’d Controller-DependentPage PACKET RETURN STATUS SCSI FIRMWARE INTERRUPT STRUCTURE SCSI Firmware Interrupt StructureSCSI FIRMWARE INTERRUPT STRUCTURE SCSI_ACTV WRITING A DRIVERSCSI_CMD SCSI_INTInterface Rules for the SCSI Firmware Passing Commands to the SCSI FirmwareBuilding the Packet Figure 5-1.SCSI Disk Driver Interface to VERSAdosInterface Rules for Multiple Callers WRITING A DRIVER Care must be taken not to modify the contents of WRITING A DRIVER Interface Rules for the SCSI Firmware FUNNEL WRITING A DRIVER Interface Rules for the SCSI Firmware WRITING A DRIVER MOVE.W 2A2,D0 THE CODE BELOW HANDLES FINAL RETURN CODES Interface Rules for a Single Caller WRITING A DRIVER Introduction TARGET ROLE ROUTINESMVME147 SCSI Firmware Background SCSI Versus SASI Rules Custom Sequence PacketCommand Table ScriptEnabling TARGET Role Enabling TARGET Role Servicing the TARGET Requests Servicing the TARGET Requests TARGET ROLE ROUTINES Servicing the TARGET Requests TARGET ROLE ROUTINES Servicing the TARGET Requests TARGET ROLE ROUTINES Introduction SCSI PACKETSTable 7-1.SCSI Functions SCSISCSI Functions cont’d Read/Write PacketTable SCSIDISK and TAPE Controller logical unit in SG table, if zero SCSI PACKETS Old Packet Supported for Compatibility+$12 in SG table, if zero |function code 3 bits DMA Scatter/Gather Table EntryRead/Write Packet 1 = link to next entryFor example $5 isCOMMAND COMMANDAttach/Detach Packet all devices CONTROLLERCOMMAND Attach/Detach Packet all devicesSCSI PACKETS +$1E FM encoding, single Controller type refer xxxxxxxx attributes byte offset +$20 Single track density Drive type 0 = 3½, 5¼ Attach/Detach Packet all devicesExample for floppy 3½, 5¼,3½, 5¼ 3½, 5¼3½, 5¼, 3½, 5¼+$04 Minimum read QIC-24 if this is set to 0, the +$00 Reserved Interrupt level +$00 +$9E $00 Format Packet Assign Alternate Sector Packet SCSI COMMAND+$0E Assign Alternate Sector Packet SCSI SCSI PACKETS DEFECT LIST TYPE0 Note 3, NOTES Head Bytes from Index MSW NoteSCSI Bus Reset Packet Controller logical unit SCSI Controller Reset Packet Erase Packet+$12 Rewind Packet Device logical unit Read Block Limits Packet SCSI PACKETS where n = number of blocks or filemarks to Space Status from SCSI The table below shows the write filemarks packet Write Filemarks PacketWrite Filemarks Packet Controller logical unit The controller must be in general or read mode Verify CRC PacketTape Mode Select/Sense Packet Tape Mode Select/Sense Packet Number of tracks on Inquiry Packet +$00 Reserved +$1A Load/Unload Packet +$14 Recover Buffer Data Packet +$0C Request Sense Data Packet Controller logical unit Check Status Packet Open Packet SCSI PACKETSOpen Packet SCSI PACKETS BYTE COMMON COMMAND SET AND DISK OPERATIONBYTE OFFSET BYTE OFFSET BYTEBYTE OFFSET ENTRY NUMBER BYTE OFFSETCOMMON COMMAND SET AND DISK OPERATION NOTESSend mode select command COMMON COMMAND SET AND DISK OPERATION BYTE OFFSET DEFECT LISTDEFECT LIST TYPE NOTESBYTE OFFSET Mode Select HeaderBYTE OFFSET Block Descriptor BYTE OFFSETBYTE OFFSET COMMON COMMAND SET AND DISK OPERATIONNOTES Block Descriptor Mode Select HeaderBYTE OFFSET BYTE OFFSETNOTES BYTE OFFSETBYTE OFFSET VALUEVALUE Mode Select Command CDBBYTE OFFSET COMMENTSBYTE OFFSET COMMON COMMAND SET AND DISK OPERATIONMode Select Header Block DescriptorPage code BYTE OFFSETBYTE OFFSET BYTE OFFSET COMMON COMMAND SET AND DISK OPERATIONNOTES TYPE ATTRIBUTE FLAGSMEDIA Mode Select HeaderMEDIA COMMON COMMAND SET AND DISK OPERATIONATTRIBUTE FLAGS TYPENOTES BYTE OFFSETBYTE OFFSET VALUEPin 2 and Pin 34 Definition for High Density PIN 34 CONTROLCOMMON COMMAND SET AND DISK OPERATION Pin 2 and Pin 34 Definition for Low DensityCOMMENTS PIN 34 CONTROLPIN 2 CONTROL Pin 34 = driveA-22