Manuals / Emerson / Computer Equipment / Computer Hardware

Emerson MVME147 manual Scsi

Models: MVME147

1 170

Download 170 pages 32.5 Kb

Page 42

SCSI

3

PACKET RETURN STATUS

Bit 15 (FINALSTAT)

1 = Intermediate return.

0 = Final status.

The script processing completed succ- essfully, OR the script processing encountered a fatal error.

Note

This does not mean that the operation that the user requested on the SCSI was successful. The status is contained in the status code (bits 7-0.)

*(L1

*(L2

*(L3

*(L4

Status word offset $18

1512 1108 0704 0300

SCSI				Request Sense

Phase	Reserved			Flags


Status				(0 if not used)

		Bit 0
		(RES)
		Re-
		served)

Bit 1 (ILI)

Incorrect length indicator.

3-2

Image 42

Emerson MVME147 manual Scsi

Contents

Introduction FeaturesGENERAL INFORMATION Modes of OperationMVME147 SCSI Firmware Entry Points The SCSI firmware initializes these vectors Equipment Supported CONTROLLE DEVICE CONTROLLECONTROLLE PARTDEVICE Devices Supported Under Common Command SetCONTROLLE PARTDOCUMENT TITLE Related DocumentationMOTOROLA PUBLICATION NUMBERManual Terminology MOTOROLAGENERAL INFORMATION CUSTOM SCSI PACKETS Initiator Role Custom PacketIntroduction CUSTOM SCSI PACKETS Initiator Role Custom Packet NOTES PHASE CODE PHASEInitiator Role Custom Packet +$00 +$68 status Note ASYNC the firmware status xxxxxxxx xxxxxxxx Page CUSTOM SCSI PACKETS Initiator Role Custom Packet CUSTOM SCSI PACKETS TARGET Enable Custom Packet TARGET Enable Custom PacketNOTES Status from SCSITARGET Enable Custom Packet TARGET Sequence Custom Packet TARGET Sequence Custom Packet CUSTOM SCSI PACKETS NOTESTARGET Sequence Custom Packet WORDS $04 and $06 CUSTOM SCSI PACKETS TARGET Sequence Custom Packet CUSTOM SCSI PACKETS TARGET Sequence Custom Packet RETRY COUNT. Not used by the TARGET role firmwareCUSTOM SCSI PACKETS PACKET RETURN STATUS Packet Return StatusControl Flags SCSI The command was retried retry count times Bit 3 FM Filemark Bit 4 COMMAND RETRY1 = Retries were performed Bit 5 COMMAND RE Packet Return Status Bit 2 EOM End of mediaPACKET RETURN STATUS Codes Table 3-1.Packet Status CodesIntermediate Return CODECODE Final Return CodesTable 3-1.Packet Status Codes Intermediate ReturnCODE Table 3-2.Packet Status Codes cont’dSCSI Bus Reset Packet section in Chapter MEANINGController-Dependent Request-Sense-Data Error-Class7 CodesTable 3-3.Packet Status Codes cont’d CODECODE SCSI Status Returned in Status PhaseTable 3-4.Packet Status Codes cont’d MEANINGCODE Request-Sense-Data Error-Class0 through 6 CodesTable 3-5.Packet Status Codes cont’d Controller-DependentPage PACKET RETURN STATUS SCSI FIRMWARE INTERRUPT STRUCTURE SCSI Firmware Interrupt StructureSCSI FIRMWARE INTERRUPT STRUCTURE SCSI_ACTV WRITING A DRIVERSCSI_CMD SCSI_INTInterface Rules for the SCSI Firmware Passing Commands to the SCSI FirmwareBuilding the Packet Figure 5-1.SCSI Disk Driver Interface to VERSAdosInterface Rules for Multiple Callers WRITING A DRIVER Care must be taken not to modify the contents of WRITING A DRIVER Interface Rules for the SCSI Firmware FUNNEL WRITING A DRIVER Interface Rules for the SCSI Firmware WRITING A DRIVER MOVE.W 2A2,D0 THE CODE BELOW HANDLES FINAL RETURN CODES Interface Rules for a Single Caller WRITING A DRIVER TARGET ROLE ROUTINES MVME147 SCSI Firmware BackgroundIntroduction SCSI Versus SASI Rules Custom Sequence PacketCommand Table ScriptEnabling TARGET Role Enabling TARGET Role Servicing the TARGET Requests Servicing the TARGET Requests TARGET ROLE ROUTINES Servicing the TARGET Requests TARGET ROLE ROUTINES Servicing the TARGET Requests TARGET ROLE ROUTINES Introduction SCSI PACKETSTable 7-1.SCSI Functions SCSISCSI Functions cont’d Read/Write PacketTable SCSIDISK and TAPE Controller logical unit in SG table, if zero SCSI PACKETS Old Packet Supported for Compatibility+$12 in SG table, if zero |function code 3 bits DMA Scatter/Gather Table EntryRead/Write Packet 1 = link to next entryFor example $5 isCOMMAND COMMANDAttach/Detach Packet all devices CONTROLLERCOMMAND Attach/Detach Packet all devicesSCSI PACKETS +$1E FM encoding, single Controller type refer xxxxxxxx attributes byte offset +$20 Single track density Drive type 0 = 3½, 5¼ Attach/Detach Packet all devicesExample for floppy 3½, 5¼,3½, 5¼ 3½, 5¼3½, 5¼, 3½, 5¼+$04 Minimum read QIC-24 if this is set to 0, the +$00 Reserved Interrupt level +$00 +$9E $00 Format Packet Assign Alternate Sector Packet SCSI COMMAND+$0E Assign Alternate Sector Packet SCSI SCSI PACKETS DEFECT LIST TYPE0 Note 3, NOTES Head Bytes from Index MSW NoteSCSI Bus Reset Packet Controller logical unit SCSI Controller Reset Packet Erase Packet+$12 Rewind Packet Device logical unit Read Block Limits Packet SCSI PACKETS where n = number of blocks or filemarks to Space Status from SCSI Write Filemarks Packet Write Filemarks PacketThe table below shows the write filemarks packet Controller logical unit The controller must be in general or read mode Verify CRC PacketTape Mode Select/Sense Packet Tape Mode Select/Sense Packet Number of tracks on Inquiry Packet +$00 Reserved +$1A Load/Unload Packet +$14 Recover Buffer Data Packet +$0C Request Sense Data Packet Controller logical unit Check Status Packet Open Packet SCSI PACKETSOpen Packet SCSI PACKETS COMMON COMMAND SET AND DISK OPERATION BYTE OFFSETBYTE BYTE BYTE OFFSETBYTE OFFSET ENTRY NUMBER BYTE OFFSETCOMMON COMMAND SET AND DISK OPERATION NOTESSend mode select command COMMON COMMAND SET AND DISK OPERATION BYTE OFFSET DEFECT LISTDEFECT LIST TYPE NOTESMode Select Header BYTE OFFSETBYTE OFFSET Block Descriptor BYTE OFFSETCOMMON COMMAND SET AND DISK OPERATION NOTESBYTE OFFSET Block Descriptor Mode Select HeaderBYTE OFFSET BYTE OFFSETNOTES BYTE OFFSETBYTE OFFSET VALUEVALUE Mode Select Command CDBBYTE OFFSET COMMENTSBYTE OFFSET COMMON COMMAND SET AND DISK OPERATIONMode Select Header Block DescriptorBYTE OFFSET BYTE OFFSETPage code COMMON COMMAND SET AND DISK OPERATION NOTESBYTE OFFSET TYPE ATTRIBUTE FLAGSMEDIA Mode Select HeaderMEDIA COMMON COMMAND SET AND DISK OPERATIONATTRIBUTE FLAGS TYPENOTES BYTE OFFSETBYTE OFFSET VALUEPin 2 and Pin 34 Definition for High Density PIN 34 CONTROLCOMMON COMMAND SET AND DISK OPERATION Pin 2 and Pin 34 Definition for Low DensityCOMMENTS PIN 34 CONTROLPIN 2 CONTROL Pin 34 = driveA-22