Extron electronic 3-10, 3-11, Operation, cont’d, GSS 100 Graphic Still Store Operation

Operation, cont’d

Advanced menu

Figure 3-10 is a flowchart that shows an overview of the Advanced menu and the available settings.

• On/still (auto-switch on and slide show off — Activates

the automatic sync detection and auto-switches to the

still image. If sync is lost, the GSS switches to the last

displayed image that was output and outputs that image

until sync is restored or you select another image to

Power Default

on Cycle

	Menu
10
sec.	Switch
	Effect
10	Menu
sec.	Output
	Config
10	Menu
sec.	Slide
	Show
10	Menu
sec.	Advanced	Next
	Menu
10	Menu
sec.	Exit
Menu
	Menu

	Menu		10 sec.		Menu	3 sec.				10 sec.
						{scroll}
	Auto Sw			Next	Name				Name	Next
	Off				GSS-100-			nn-nn-nn
					Name (Display Only)
				(Changeable under RS-232/Ethernet control;
	Auto Switch			scrolls to the left if greater than 8 characters.)
•	Off	•	Off/show
•	On/still	•	On/show
					Menu				Menu
					nn:nn:nn Next			Int Temp		Next
					nn:nn:nn			113F 45C
					MAC Address			Temperature
					(Display Only)			(Display Only)
	Menu						Menu
	RS-232		Next				I192.168		Next
	9600						P254.254

display.

• On/show (auto-Switch on and slide show on) —

Activates the automatic sync detection and auto-switches

to the slide show. If sync is lost, the GSS switches to the

last-displayed image and begins to cycle through the

available images.

The default setting is off.

Name display

The read-only Name display shows either the factory default name or a customized name that can be assigned under RS-232 or Ethernet control. If the name is greater than eight characters, the display shows the first eight characters of the assigned name and then scrolls the name to the left to display the remaining characters of the name.

The factory default name is the product name (GSS-100-) plus last three pairs of MAC address. See chapter 4, SIS™ Control, and chapter 5, HTML Control and IPL File Manager, to assign a

	Baud Rate			TAKE	Press Take to	TAKE	Press Take to enable
• 2400		•	19200		enable changing		changing the value
•	4800	•	38400		the value.		and select an octet.
•	9600	•	115200		Rotate Adjust/		Rotate Adjust/Select
					Select to change		to change the value in
					the value.		the selected (blinking)
							octet.

Figure 3-10 — Advanced submenu flowchart

Auto Switch (and slide show) submenu

The GSS can be set to an auto-switch mode that monitors the sync signal on the RGB pass-through input and automatically switches to the last-displayed stored image or slide show for output when sync is lost. This submenu also allows you to turn the auto-switching and slide show on and off.

Rotate the Adjust/Select mode while in the Auto-Switch submenu to select:

•Off (auto-switch mode off and slide show off) — Deactivates the automatic sync detection the slide show.

•Off/show (auto-switch off and slide show on) — Leaves the automatic sync detection off and manually initiates the slide show. If the pass-through input was being displayed when this selection is made, the GSS displays the first image alphabetically by file name.

name.

MAC Address display

The read-only MAC Address display shows the hardcoded, factory assigned hardware address.

Internal Temperature display

The read-only Internal Temperature display shows the Fahrenheit and Celsius measurements for the GSS temperature.

CAUTION Temperatures above 150 degrees Fahrenheit(65 degrees Celsius) are potentially damaging to the GSS.

3-10 GSS 100 Graphic Still Store • Operation GSS 100 Graphic Still Store • Operation 3-11