Extron electronic MPX Plus 866 A manual EDX6$*X6-GRPM

PRELIMINARY

DSP SIS Commands, cont’d

Command	ASCII command	Response	Additional
	(host to switcher)	(switcher to host)	description

Audio group master commands

N• See “Group masters“, in chapter 5, “Switcher Software“, for more information about audio group masters.

•You must have assigned members to a group for these commands to have an effect.

•For X6%, a positive (+) value is assumed unless you specify otherwise (-).

•If you enter a X6% value that is outside the valid range for the group or outside the soft limits, the switcher responds with an “invalid parameter” (E13) error.

•X6%, X6^, and X6& values can be sent without leading zeroes; responses are alway 5 digits.

Set a group fader control	EDX6$*X6%GRPM}	GrpmX6$*X6%]		Set the group fader to a
				value of X6%.
Example:	Ed2*-293*GRPM}	GrpmD02*-00293*GRPM]Set the group 2 fader control
				to -29.3 dB.
Raise a group fader control	EDX6$*X6^+GRPM}	GrpmX6$*X6%]		Increase the level of the X6$
				group fader by X6^ dB.
Example	Ed2*30+GRPM}	GrpmD02*-00263*GRPM]Raise the group 2 fader 3 dB
				(from -29.3 dB to -26.3 dB,
				starting from the level set
				in the “Set a group fader
				control” example, above.
Lower a group fader	EDX6$*X6^-GRPM}	GrpmX6$*X6%]		Decrease the level of the X6$
control				group fader by X6^ dB.
View the group fader	EDX6$GRPM}	GrpmX6$*X6%]		In verbose modes 1 and 2, the
control level				response is simplified to
				X6%].
Mute a group mute control	EDX6$*1GRPM}	GrpmDX6$*+00001]		Mute all blocks in group X6$.
Clear (unmute) a group	EDX6$*0GRPM}	GrpmDX6$*+00000]		Umute all blocks in group
mute control				X6$.
View a group mute control	EDX6$GRPM}	GrpmDX6$*X6#]		For group masters, X6#
				is always expresed as a
				positive, 5-digit value.
Set soft limits	ELX6$*X6&upper*X6&lowerGRPM}			Set the groups soft limits to
		GrpmLX6$*X6&*X6&]		X6& and X6&.
Example:	EL2*-48*-630GRPM}	GrpmL02*-00048*-00630]Set the upper soft limit for
				the group 2 fader to -4.8 dB
				and the lower limit to -63 dB.
View soft limits	ELX6$GRPM}	GrpmLX6$*X6&*X6&]		In verbose modes 1 and 2,
				the response is simplified to
				X6&*X6&].
View group type	EPX6$GRPM}	GrpmPX6$*X6*]		Show the group type (X6*)
				for group X6$. In verbose
				modes 1 and 2, the response
				is simplified to X6*].
View group members	EOX6$GRPM}	GrpmOX6$*X6)1*X6)2*...*X6)16]
				X6)is the control or mix point.
				In verbose modes 1 and 2,
				the response is simplified to
				X6)1*X6)2*...*X6)16].
Reset a group	EZX6$GRPM}	GrpmZX6$]		Delete all members from
				group X6$, reset parameters
				and soft limits.
N X6) = Gain control or mic mix-point See the tables on page B-4 and B-5.
X6# = Mute status		0 = unmute	1 = mute
X6$ = Group master group number		01 - 32
X6%, X6^, X6& = Group fader soft limit		dB value, in 0.1 dB increments, see page B-3.
X6* = Group type (see figure B-1)		6= gain (A through D)		12 = mute

18 = gain (E and F)

B-10 MPX Plus 866 A Media Presentation Matrix Switcher • DSP SIS Commands