FEIN Power Tools WSG15-70LNOX/N09 manual 20 en, For your safety, Intended use of the power tool

OBJ_BUCH-0000000123-002.book Page 20 Tuesday, August 13, 2013 9:40 AM

20en

Character		Unit of measure-	Unit of measure-	Explanation
		ment, international	ment, national
		mm	mm	M=Thread for clamping flange
				l=Length of mounting thread
		kg	kg	Weight according to EPTA-Procedure 01/2003
LpA		dB	dB	Sound pressure level
LwA		dB	dB	Sound power level
LpCpeak		dB	dB	Peak sound pressure level
K...				Uncertainty
		m/s2	m/s2	Vibrational emission value according to EN 60745
				(vector sum of three directions)
	h,AG	m/s2	m/s2	Mean vibrational value for angle grinding
	h,DS	m/s2	m/s2	Mean vibrational value for sanding with sanding
				sheet
		m, s, kg, A, mm, V,	m, s, kg, A, mm, V,	Basic and derived units of measurement from the
		W, Hz, N, °C, dB,	W, Hz, N, °C, dB,	international system of units SI.
		min, m/s2	min, m/s2

For your safety.

WARNING	Read all safety warnings and all
	instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this Instruction Manual and the enclosed “General

Safety Instructions” (document number

341 30 054 06 1). The documents mentioned should be kept for later use and enclosed with the power tool, should it be passed on or sold.

Please also observe the relevant national industrial safety regulations.

Intended use of the power tool:

Hand-guided angle grinder for dry grinding/roughing and cutting of metal and stone in weather-protected environ- ments with the application tools and accessories recom- mended by FEIN.

This power tool is also suitable for use with AC genera- tors with sufficient power output that correspond to the Standard ISO 8528, design type G2. This Standard is par- ticularly not complied with when the so-called distortion factor exceeds 10 %. When in doubt, please refer to the generator instruction/specification guide.

Safety Warnings common for Grinding, Sanding, Wire Brushing or Abrasive Cutting Off Operations

This power tool is intended to function as a grinder, sander, wire brush or cut-off tool. Read all safety warn- ings, instructions, illustrations and specifications pro- vided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Operations such as polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.

Do not use accessories which are not specifically designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power tool, it does not assure safe operation.

The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Acces- sories running faster than their rated speed can break and fly apart.

The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.

Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or acces- sory is dropped, inspect for damage or install an undam- aged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this testtime.

Wear personal protective equipment. Depending on appli- cation, use face shield, safety goggles or safety glasses. Where appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your opera- tion. Prolonged exposure to high intensity noise may cause hearing loss.