First Alert FA148CPSSIA Reports In Armed Period Per, Download Information, ∗94 Download Phone No

∗93	Reports In Armed Period Per
	Zone (Swinger Suppression)
	Restrict Report Pairs:
	0	= Unlimited Reports
	1	= 1 report pair per zone per armed
		period
	2	= 2 report pairs per zone per armed
		period

[1,0]

Restrict SIA-Compliant Controls:

Report Pairs Unlimited Reports Enable

Selection limits the number of alarm/alarm restore message pairs per zone sent to the CS in an armed period. Swinger suppression applies to burglary zones only.

SIA Guidelines: Must be set for option 1 or 2

SIA-Compliant Controls:

Restrict Report Pairs:

1 = 1 report pair; 2 = 2 report pairs

Unlimited Reports Enable:

0 = restrict reports to the setting in entry 1

1 = unlimited reports for zones listed in zone list 7; (use zone list 7 to enter those zones that require unlimited reporting; these zones ignore the setting in entry 1)

DOWNLOAD INFORMATION (✱94, ✱95)

∗94 Download Phone No.

Enter up to 20 digits, 0–9; #+11 for '✱'; #+12 for '#'; #+13 for a 2-second pause. Do not fill unused spaces. If fewer than 20 digits, exit field by pressing ✱. To clear entries from field, press ✱94✱.

Enter the phone number of the downloading computer.

UL: downloading may be performed only if a technician is at the site. Up/downloading via the Internet has not been evaluated by UL.

∗95	Ring Count For Downloading
				[15]
	0 = Disable Station Initiated Download;
		Refer to the chart below and program accordingly.
	1–14 = number of rings (1–9, # +10 =10,
	# +11 =11, # +12 =12, # +13 =13,		phone		answer	down-	Set field ∗95 to…
	# +14 =14);		module		machine	loading
			yes		no	no	1-14 (not 0)
	15 = answering machine defeat
			yes		yes	no	greater than rings set on answer machine
	(# +15 =15).
							(e.g., if ans. machine is 4 rings, set this
	NOTE: Do not enter 0 if using 4286						field to 5). This allows access to the
	Phone Module.						phone module if the answer machine is
							off.
			yes		no	yes	1-14 (not 0)
			yes		yes	yes	15 (bypasses answer machine†)
			no		no	no	0
			no		yes	no	0
			no		no	yes	1-14
			no		yes	yes	15

†NOTE: If “15” is entered to bypass an answering machine, and a 4286 Phone Module is included in the system, you should note the following:

When calling in from an off-premises phone, the user should make the initial call, allow 1 or 2 rings only, then hang up, then call again. The phone module will now seize the line, and 2 long tones sound, followed by the usual voice prompt for the access code. If this procedure is not followed, phone module operation will not be possible.

∗96, ∗97 Initialize/Reset Defaults (These are commands, not data fields. See page 3.) ∗98, ∗99 Exit Commands (These are commands, not data fields. See page 3.)

PAGER OPTIONS (✱160- ✱172)

The system can send various reports to several pagers (FA168CPS = up to 4; FA148CP = up to 2). To program pager reporting, do the following:

1.Enter the pager phone number(s), preface characters, and pager report options in data fields *160 - *171.

2.Enable Pager Delay, if desired, in field *172 (delays alarm reporting for ALL pagers).

3.Make sure appropriate user open/close pager reports are enabled (see Security Codes section in User Guide). Users that perform actions in partition 1 will, if enabled, attempt to report to all pagers enabled for open/close reporting in partition 1. Users that perform actions in partition 2 will, if enabled, attempt to report to all pagers enabled for open/close reporting in partition 2.

4.If using latchkey pager report, define the latchkey report schedule using Scheduling mode (master code + [#] [6] [4] then select event type 03). System must be armed for the Latchkey report to be sent.

5.If using a function key to manually send a message to a pager, use *57 Function Key Menu mode to define the key (function 01).

6.If reporting zone alarms and troubles to a pager, use *81 Zone List menu mode to assign the zones associated with each pager (zone lists 9-12†).

†FA148CP supports zone lists 9 and 10 only.

–12 –