80 Menu Mode
|
|
|
|
|
| Output Function No. | Enter the output function number to be defined (or 00 to exit) | |
| Output Funct. # | |||||||
| (FA168CPS: |
|
| |||||
| (00 = Quit) |
| 01 |
|
| |||
|
| (FA148CP: |
|
| ||||
|
|
|
|
|
| [∗] to continue; 00 to quit |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Summary Screen | This screen displays a summary of the current output | |
| 01 | A | E | P | Trig | |||
| [∗] to continue | programming (for this example, Zone List has been | ||||||
| ?00 | 0 | 0 | – | ZL=00 | |||
|
| is the default screen). | ||||||
|
|
|
|
|
|
| A = Output Action; E = Triggering event; P = Partition; | |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Trig = Trigger type | |
|
|
|
|
|
|
| NOTE: A question mark in the summary screen indicates that the | |
|
|
|
|
|
|
| device number shown has not been mapped. Use *79 Menu | |
|
|
|
|
|
|
| mode to map the device. | |
|
|
|
|
|
| Activated By | Select where the initiating event for this output definition is to | |
| 01 Activated By: | |||||||
| 0 = delete | occur as follows: | ||||||
| Zone List |
|
| |||||
|
|
| 1 = zone list (go to “A”) | If you enter “0,” the following prompt appears: | ||||
|
|
|
|
|
| 2 = zone type (go to “B”) | Delete? |
|
|
|
|
|
|
| 3 = zone number (go to “C”) |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| [∗] to continue | 0 = NO, 1 = YES |
|
|
|
|
|
|
|
|
|
|
Press 1 to delete this output definition. The system deletes the output function and any previous programming.
A”
01 Zn List
1
Zone List
(prompt appears if zone list was selected)
Enter the desired zone list number associated with this output number. At the ENTER EVENT prompt, enter the zone list event that will activate this output
NOTE: Do not use pager zone lists
Enter Event
Alarm 1
0 = restore; 1 = alarm;
2 = fault; 3= trouble
|
|
|
| NOTE: For alarm, fault, and trouble, an event on ANY zone in the | |||||||
|
|
|
| list activates the output, but ALL zones in the list must be | |||||||
|
|
|
| restored before the output is restored. |
|
| |||||
|
|
|
| Press [✱] to continue and skip to the “Output Action” prompt. | |||||||
| “B” |
| Zone Type | (prompt appears if zone type was selected) |
| ||||||
|
|
| See list at right for available | Enter the desired zone type associated with this output number. | |||||||
| 01 Enter Zn type |
| |||||||||
|
| zone types. | At the PARTITION prompt, enter the partition in which this zone | ||||||||
| Perimeter | 03 | |||||||||
|
| type will occur. |
|
|
|
|
|
| |||
|
|
|
| CHOICES FOR ZONE TYPES: |
|
|
| ||||
|
|
|
|
|
|
| |||||
|
|
|
| 00 | = Not Used | 05 | = Day/Night | 12 | = Monitor Zone | ||
|
|
|
| 01 | = Ent/Exit #1 | 06 | = 24 Hr Silent | 14 | = Carbon Monoxide†† | ||
|
|
|
| 02 | = Ent/Exit #2 | 07 | = 24 Hr Audible | 16 | = Fire w/verification | ||
|
|
|
| 03 | = Perimeter | 08 | = 24 Hr Aux | 23 | = No Alarm Response | ||
|
|
|
| 04 | = Interior Follower | 09 | = Fire | 24 | = Silent Burglary | ||
|
|
|
|
|
| 10 | = Interior w/Delay | 77 | = Keyswitch Zone | ||
|
|
|
|
|
|
|
|
| 81 | = AAV Monitor Zone | |
|
|
|
|
|
|
|
|
| |||
|
|
|
| CHOICES FOR SYSTEM OPERATION: |
| ||||||
|
|
|
| 20 | = | 36 | = **At Bell Timeout*** | 58 | = Duress | ||
|
|
|
| 21 = | 38 = Chime |
| 60 | = AAV | |||
|
|
|
| 22 | = Disarming | 39 | = Any Fire Alarm |
| 61 | = AVS/GSMV session begin§ | |
|
|
|
| 31 | = End of Exit Time | 40 | = Bypassing |
| 62 | = AVS/GSMV session end § | |
|
|
|
| 32 | = Start of Entry Time | 41 | = **AC Power Failure | 66 | = Function Key† | ||
|
|
|
| 33 | = Any Burglary Alarm | 42 | = **System Battery Low 67 | = Bell Fail | |||
|
|
|
|
|
| 43 | = Comm. Failure |
| 68 | = Telco Line Cut | |
|
|
|
|
|
| 52 | = Kissoff |
| 78 | = Keyswitch Red LED | |
|
|
|
|
|
| 54 | = Fire Zone Reset |
| 79 | = Keyswitch Green LED |
**Use 0 (Any) for Partition No. (P) entry.
***Or at Disarming, whichever occurs earlier.
† Use *57 Menu Mode to assign the function key (function “07”).
††when used with an output function, the carbon monoxide zone type activates upon CO alarms only. Does not activate for trouble conditions. § automatically set when appropriate AVS Quick Command performed.
Note: In normal operation mode:
Code + # + 7 + NN Key Entry starts Device NN.
Code + # + 8 + NN Key Entry stops Device NN.
Enter the partition in which this zone type will occur.
| 01 Partition | 0 | = any partition; 1 = partition 1; | |
|
|
|
|
|
|
|
|
| |
| Any partition 0 | 2 | = partition 2; 3 = common |
Press [✱] to continue and skip to the “Output Action” prompt.