∗66 | Arm Away/Stay Rpt Code |
| See above for entries. |
[0,0,0,0,0,0]
Away Stay | Away Stay | Away Stay |
Part. 1 | Part. 2 | Common |
This option allows for independent programming of Away and Stay reports for each partition, including the common lobby.
NOTE: “OPEN” reports are not sent if the associated closing report is not enabled.
∗67 | RF Trans. Low Bat Report Code |
| |
[00] |
See above for entries.
Sent when a transmitter
∗68 |
| Cancel Report Code | ||
|
| See above for entries. | ||
|
|
| [10] | |
|
|
| Report enabled. |
|
|
|
|
|
|
[00] |
Sent upon disarming the system after an alarm condition was reported.
∗69 |
| Recent Closing Report Code | ||
|
| Not applicable to FA148CP/FA168CPS | ||
|
| See above for entries. | ||
|
|
|
|
|
|
|
|
| |
|
|
| Always enabled. | |
|
|
|
|
|
|
|
|
|
|
[11] |
RESTORE REPORT CODES (✱70 – ✱76)
∗70 | Alarm Restore Rpt Code |
| See above for entries. |
[0]
Alarm restore signals indicate that respective alarm zone(s) are no longer faulted. Alarm restore reports are sent to the central station at bell timeout (field *33), if the zone(s) in alarm are actually restored to a
See UL System Reporting Note above *59.
If Reports Per Armed Period Per Zone (*93) is also programmed, the system will report alarm and restore codes as described above until the “Reports Per Armed Period” count is reached. Disarming and rearming will reset the “Reports Per Armed Period” count.
| ∗71 | Trouble Restore Rpt Code |
|
|
|
| [00] |
| |||
|
| See above for entries | Sent when a trouble in a zone is restored and code + OFF performed. | ||
|
|
| |||
|
|
| See UL System Reporting Note above *59. |
| |
|
|
|
|
|
|
|
| Bypass Restore Rpt Code |
|
|
|
| ∗72 |
|
|
| |
| [00] |
| |||
|
| See above for entries. | Sent when a zone that has been bypassed is unbypassed. | ||
|
|
|
See UL System Reporting Note above *59.
| ∗73 | AC Restore Rpt Code |
|
|
|
| [00] |
| |||
|
| See above for entries. |
|
|
|
|
| Sent after AC power has been restored after an AC power outage. | |||
|
|
| |||
|
|
| See UL System Reporting Note above *59. |
| |
|
|
|
|
|
|
|
| Low Bat Restore Rpt Code |
|
|
|
| ∗74 |
|
|
| |
| [00] |
| |||
|
| See above for entries. | Sent after a system | ||
|
|
|
See UL System Reporting Note above *59.
∗75 | RF Trans. Lo Bat Rst Rpt Code |
| See above for entries. |
[00] |
Sent when a transmitter’s low battery condition is restored (i.e., new battery installed).
UL: must be enabled if wireless devices are used. See UL System Reporting Note above *59.
∗76 | Test Restore Rpt Code |
| |
[00] |
See above for entries.
This is sent when the Test mode is exited or upon timeout (4hrs). See UL System Reporting Note above *59.
– 9 –