First Alert FA148CPSSIA manual WORKSHEET FOR ∗80 OUTPUT FUNCTION PROGRAMMING

WORKSHEET FOR ∗80 OUTPUT FUNCTION PROGRAMMING

Fill in the required data on the worksheet below and follow the programming procedure in the installation manual as you enter the data during the displays and prompts that appear in sequence.

Notes: 1. For Relays, 4229 and 4204 devices are programmed in *79, *80, and *81 modes.

2.For Powerline Carrier devices (plcd), field ✱27 must be programmed with a House Code.

3.Tampers of expansion units cannot be used to operate devices.

Output	Activation Type and Detail				Partition	Event (for zone list/activated by)		Action	Output	Device
Function	Activated by	Zone List	Zone Type	Zone No.	Number	By Zone List	By Zone No.	0 = off	Number	Type
Number	0=delete	(ZL)	(ZT)	(ZN)	(P)			1 = close 2 secs
(FA168CPS:	1=zn list	1-8 = list	(see table	00=none	(if using ZT trig)	0 = restore	0 = restore	2 = stay closed	FA168CPS:	R = relay
1-48)	2=zn type		below)	FA168CPS:	0 = any	1 = alarm	1 = alrm/flt/trbl	3 = pulse	1-18	T = trigger
(FA148CP:	3=zn no.			01-64	1 = partition 1	2 = fault		4 = toggle		X = X10
1-24)				FA148CP:	2 = partition 2	3 = trouble		5 = duration 1††	FA148CP:
				01-06, 09-34,
					3 = common			6 = duration 2††	1-8, 17, 18
				49-56
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48

ZONE TYPE/SYSTEM OPERATION – Choices for Zone Types are:

00	= Not Used	05	= Trouble Day/Alarm Night			10 = Interior w/Delay			24 = Silent Burglary
01	= Entry/Exit#1	06	= 24 Hr Silent			12 = Monitor Zone			77 = Keyswitch
02	= Entry/Exit#2	07	= 24 Hr Audible			14 = Carbon Monoxide			81 = AAV Monitor Zone
03	= Perimeter	08	= 24 Hr Aux			16 = Fire w/Verification			90-91 = Configurable
04 = Interior Follower		09	= Fire			23 = No Alarm Response
Choices for System Operation are:											Note: In normal operation mode:
20	= Arming–Stay			38	= Chime		58	= Duress
											Code + # + 7 + NN Key Entry starts Device
21	= Arming–Away			39	= Any Fire Alarm		60	= AAV Trigger
											Code + # + 8 + NN Key Entry stops Device
22	= Disarming (Code + OFF)			40 = Bypassing			61	= AVS/GSMV session begin §
31	= End of Exit Time			41	= **AC Power Failure		62	= AVS/GSMV session end §
										** Use 0 (any) for Partition No. (P) entry.
32	= Start of Entry Time			42	= **System Battery Low		66	= Function key†
33	= Any Burglary Alarm			43	= Communication Failure		67	= Bell Failure		*** Or at Disarming, whichever occurs earlier.
36	= **At Bell Timeout***			52 = Kissoff			68	= TELCO Line Fault		† Use *57 Menu mode to assign the function key.
				54	= Fire Zone Reset		78	= Keyswitch red LED†††		†† Duration is set in program field *177.
							79	= Keyswitch green LED†††		††† Device action not used for these choices.
										§ automatically set when appropriate AVS Quick

Command performed.

– 38 –