Fostex CR300 owner manual Mode Of Recording, Automatic digital-sourcesynchro recording 1-track

MODE OF RECORDING

This section introduces the summary of the modes of recording available with this unit.

It is recommended to use the automatic digital-source synchro recording when

recording a CD, DAT, MD or DCC source (S/P DIF only).

The track numbers are updated automatically by this unit.

For details, also refer to the corresponding descriptions.

This unit provides four mode of recording on CD-R and CD-RW discs.

Select a mode according to the source recorded.

Automatic digital-source synchro recording (1-track)

Automatic digital-source synchro recording (all-track)

Automatic finalization

recording

Manual digital-source

recording

Analog-source recording

........... When the source equipment starts to play, only one track is recorded automatically and the

recording stops automatically after that track. This mode is convenient for edited recording of a CD, DAT, MD or DCC. (Refer to page 18 for the recording setup procedure.)

......... When the source equipment starts to play, all tracks are recorded automatically and the

recording stops automatically after the last track. This mode is convenient for recording an entire CD, DAT, MD or DCC. (Refer to page 19 for the recording setup procedure.)

........... This mode automatically performs finalization after an all-track automatic digital source synchro

recording. (Refer to page 20 for the recording setup procedure.)

........... This mode is mainly used for recording the output from other digital sources than those

mentioned above. Recording is started or stopped manually. (Refer to page 21 for the recording setup procedure.)

........... This mode is used for recording the line output of the source equipment. (Refer to page 22 for

the recording setup procedure.)

To monitor the recording input, set the INPUT SELECTOR to desired input position. Even if the position is the same, it must be changed to a different position and then switched back to monitor the input.

INPUT SELECTOR

DIGITAL		ANALOG
COAX	XLR/+4	XLR/-10
	•
•		•
OPT •		• LINE
AESEBU/ •

When the input is selected, the input source equipment name is displayed as "INPUT" ➔ "CD"(only from digital input) ➔ "MONI".

•This display is available if the input source is a CD, MD, DAT or DCC.

•Before recording from LaserDisc, make sure that this unit’s sampling frequency indicator lights in the display. Digital recording is not possible if this indicator does not light. Check the source with the record monitor.

•When recording from digital sources like CD, CDV, or LD players, the input source display may display “CD.”

•A digital input source other than mentioned above such as AES/EBU is displayed as "-- --" .

CAUTION

This unit is a recorder for writable compact discs.

This recorder can record on discs carrying the CD-R mark*1, the CD-RW mark*2. The CD-R indicator lights when a CD-R (Compact Disc - Recordable) is loaded while the CD-RW indicator lights when a CD-RW (Compact Disc - Rewritable) is loaded. Recording on a partially recorded disc starts from the point where the previous recording left off. The CD-R disc is recordable once and cannot be erased once recorded. The CD-RW disc is recordable and can erased and rerecorded again. In the following cases, recording is impossible even when the RECORD or DIGITAL SYNCHRO button is pressed.

When the CD indicator is lit (CD or finalized CD-R), input monitoring is started by pressing any of the above buttons. When the CD-RW and FINALIZE indicators are lit (finalized CD-RW), input monitoring is started by pressing any of the above buttons.

When there is no remaining recording time and "REC FULL" is displayed.

When 99 tracks have been recorded and "REC FULL" is displayed. (No more recording is possible.)

When a CD-R or CD-RW disc is inserted, the unit automatically performs a series of adjustments designed to provide the best possible recording.

It may take some time to complete the automatic adjustments if the unit is cold when the power is turned on. Please wait for the recorder to enter the record standby mode.

Be sure to remove the disc before turning off the power. If the disc is left in the recorder, it may not operate normally next time.

16

CR300 <PRB1291-A>