Manuals
/
Fujitsu
/
Computer Equipment
/
Server
Fujitsu
B120 manual
Models:
B120
1
3
68
68
Download
68 pages
12.34 Kb
1
2
3
4
5
6
7
8
<
>
Troubleshooting
Install
Error codes
Replacement of SCSI hard disk drive during operation
Warranty
Configuring the server
Instructions on connecting and disconnecting cables
any technical problems or other questions you need clarified?
Diagnostic System
Setting up the tower server
Page 3
Image 3
Page 2
Page 4
Page 3
Image 3
Page 2
Page 4
Contents
PRIMERGY B120
Intel-based Server Systems
OPERATING MANUAL
your sales outlet
any technical problems or other questions you need clarified?
Please contact one of our service partners your sales partner
Are there
Page
A26361-K646-Z102-1-7619
Property and data protection Troubleshooting and tips
PRIMERGY B120
Operating Manual
Introduction Important notes Installation
This manual was produced by
Pentium is a registered trademark of Intel Corporation, USA
Copyright ã Fujitsu Siemens Computers GmbH
Offenders will be liable for damages
Contents
3 Installation
9 Index
Contents
Hard disk subsystem
1.1 Features
1 Introduction
System board
Introduction
Features
Power supply
Service and Support
Notational conventions
Technical data
Electrical data standard power supply
1.2 Notational conventions
Environmental conditions
Technical data
Standards
Mechanical data
Before operating the device
2.1 Safety
Installation and operation
2 Important notes
Batteries
Safety
Poper operation of the system, warranty features
Important notes
Other important notes
2.2 CE certificate
CE certificate
Modules with electrostatic sensitive components
2.3 FCC Class B Compliance Statement
2.4 Transporting the server
Important notes
Note on saving energy
2.5 Disposal and recycling
Disposal and recycling
Environmentally friendly product design and development
Page
3 Installation
3.1 Installation steps
3.2 Unpacking the server
Connecting cables
3.3 Instructions on connecting and disconnecting cables
3.4 Setting up the tower server
Installation
200 V - 240
3.4.1 Connecting the tower server to the line voltage
Setting up the tower server
100 V - 125
3.5 Installing rack-server in/removing from rack
3.4.2 Connecting the monitor to the line voltage
Installation
Installing rack-server in/removing from rack
3.5.1 Mounting the slide-in module
Installation
A26361-K646-Z102-1-7619
Installation
Installing rack-server in/removing from rack
Ê Push the server up to the front panel
Installation
3.5.2 Installing the slide-in module
Fitting spring nuts
Installing rack-server in/removing from rack
Installation
Mounting cage nuts
100 V - 125
3.5.3 Connecting the rack server to the line voltage
Installing rack-server in/removing from rack
Installation
3.6 Prepare the keyboard
Prepare the keyboard
Installation
Tower
3.7 Connecting devices to the server
Connecting devices to the server
Installation
Installation
Enabling access to the accessible drives
4 Preparation for use and operation
4.1 Unlocking/locking the tower server
Enabling access to the hard disk drives
Preparation for use and operation
A26361-K646-Z102-1-7619
A26361-K646-Z102-1-7619
4.2 Operation controls
Operation controls
Preparation for use and operation
Power-on indicator
4.2.2 Indicators
4.2.3 Drive indicators
ON/OFF switch
monitor screen
4.3 Switching the server on and off
Switching the server on and off
Preparation for use and operation
Other switch-on methods
Switching the server on and off
Server is switched off
Server is switched on
4.4.3 Installing the operating system
4.4 Configuring the server
4.4.1 Configuration with ServerStart
4.4.2 Configuration without ServerStart
A26361-K646-Z102-1-7619
4.5 Locking the tower server
Fitting the hard disk cover
Preparation for use and operation
Preparation for use and operation
4.6 Cleaning the server
Cleaning the server
Locking the server
Page
5.1 Opening and closing the tower server
5 Opening and closing the server
Opening and closing the server
5.2 Opening and closing the rack server
Opening and closing the rack server
Opening and closing the server
A26361-K646-Z102-1-7619
Page
6 Property and data protection
Page
Power cord incorrectly connected
7 Troubleshooting and tips
7.1 Operation indicator remains dark
7.2 The server switches itself off
7.5 No screen display or display drifts
Troubleshooting and tips
Power cable or monitor cable not connected
7.4 Flickering stripes on the monitor screen
7.6 No mouse pointer displayed on the screen
7.9 System does not boot
Mouse controller disabled
SCSI configuration incorrect standard SCSI controller
Disk Array Controller is not configured for this hard disk drive
7.10 Drives dead at system boot
7.12 Error messages on the screen
The Disk Array Controller configuration is incorrect
8.1 The SCSI hard disk subsystem
8 System components and expansions
RAID level 1 and 5 without standby hard disk
8.1.1 SCSI hard disk drives
System components and expansions
RAID level 0 and
The SCSI hard disk subsystem
8.1.2 Replacement of SCSI hard disk drive during operation
Function of the indicators Green indicator
Orange indicator
System components and expansions
8.1.3 Installing/removing a SCSI hard disk drive
8.1.4 SCSI platter for four 1-inch hard disk slide-in modules
The SCSI hard disk subsystem
System components and expansions
System components and expansions
8.2 Accessible drives
IDE drive
SCSI drive
8.2.1 Installing/Removing an accessible 5 ¼-inch drive
Accessible drives
System components and expansions
System components and expansions
8.2.2 Changing the floppy disk drive
8.3 Removing/installing boards
Removing/installing boards
System components and expansions
8.4.1 Installing/removing the chipDISK
8.4 chipDISK for RemoteView
System components and expansions
System components and expansions
8.4.2 Configuring the chipDISK
Diagnostic System
chipDISK for RemoteView
System components and expansions
8.5 Replacing the system fan
System components and expansions
8.6 Adapter module
8.7 System board
Adapter module
Page
9 Index
K Keyboard
Index
Index
Index