Manuals
/
Fujitsu
/
Computer Equipment
/
Server
Fujitsu
B120 manual
Models:
B120
1
44
68
68
Download
68 pages
12.34 Kb
41
42
43
44
45
46
47
48
<
>
Troubleshooting
Install
Error codes
Replacement of SCSI hard disk drive during operation
Warranty
Configuring the server
Instructions on connecting and disconnecting cables
any technical problems or other questions you need clarified?
Diagnostic System
Setting up the tower server
Page 44
Image 44
Page 43
Page 45
Page 44
Image 44
Page 43
Page 45
Contents
OPERATING MANUAL
PRIMERGY B120
Intel-based Server Systems
any technical problems or other questions you need clarified?
Please contact one of our service partners your sales partner
Are there
your sales outlet
Page
A26361-K646-Z102-1-7619
PRIMERGY B120
Operating Manual
Introduction Important notes Installation
Property and data protection Troubleshooting and tips
Pentium is a registered trademark of Intel Corporation, USA
Copyright ã Fujitsu Siemens Computers GmbH
Offenders will be liable for damages
This manual was produced by
3 Installation
Contents
Contents
9 Index
1.1 Features
1 Introduction
System board
Hard disk subsystem
Features
Power supply
Service and Support
Introduction
Technical data
Electrical data standard power supply
1.2 Notational conventions
Notational conventions
Technical data
Standards
Mechanical data
Environmental conditions
2.1 Safety
Installation and operation
2 Important notes
Before operating the device
Safety
Poper operation of the system, warranty features
Important notes
Batteries
2.2 CE certificate
CE certificate
Modules with electrostatic sensitive components
Other important notes
Important notes
2.3 FCC Class B Compliance Statement
2.4 Transporting the server
2.5 Disposal and recycling
Disposal and recycling
Environmentally friendly product design and development
Note on saving energy
Page
3.2 Unpacking the server
3 Installation
3.1 Installation steps
3.3 Instructions on connecting and disconnecting cables
3.4 Setting up the tower server
Installation
Connecting cables
3.4.1 Connecting the tower server to the line voltage
Setting up the tower server
100 V - 125
200 V - 240
Installation
3.5 Installing rack-server in/removing from rack
3.4.2 Connecting the monitor to the line voltage
Installation
Installing rack-server in/removing from rack
3.5.1 Mounting the slide-in module
Installation
Installing rack-server in/removing from rack
Ê Push the server up to the front panel
A26361-K646-Z102-1-7619
3.5.2 Installing the slide-in module
Fitting spring nuts
Installing rack-server in/removing from rack
Installation
Mounting cage nuts
Installation
3.5.3 Connecting the rack server to the line voltage
Installing rack-server in/removing from rack
Installation
100 V - 125
Installation
3.6 Prepare the keyboard
Prepare the keyboard
3.7 Connecting devices to the server
Connecting devices to the server
Installation
Tower
Installation
4.1 Unlocking/locking the tower server
Enabling access to the accessible drives
4 Preparation for use and operation
A26361-K646-Z102-1-7619
Enabling access to the hard disk drives
Preparation for use and operation
4.2 Operation controls
Operation controls
Preparation for use and operation
A26361-K646-Z102-1-7619
4.2.2 Indicators
4.2.3 Drive indicators
ON/OFF switch
Power-on indicator
4.3 Switching the server on and off
Switching the server on and off
Preparation for use and operation
monitor screen
Switching the server on and off
Server is switched off
Server is switched on
Other switch-on methods
4.4 Configuring the server
4.4.1 Configuration with ServerStart
4.4.2 Configuration without ServerStart
4.4.3 Installing the operating system
4.5 Locking the tower server
Fitting the hard disk cover
Preparation for use and operation
A26361-K646-Z102-1-7619
4.6 Cleaning the server
Cleaning the server
Locking the server
Preparation for use and operation
Page
5 Opening and closing the server
5.1 Opening and closing the tower server
5.2 Opening and closing the rack server
Opening and closing the server
A26361-K646-Z102-1-7619
Opening and closing the rack server
Opening and closing the server
Page
6 Property and data protection
Page
7 Troubleshooting and tips
7.1 Operation indicator remains dark
7.2 The server switches itself off
Power cord incorrectly connected
Troubleshooting and tips
Power cable or monitor cable not connected
7.4 Flickering stripes on the monitor screen
7.5 No screen display or display drifts
7.9 System does not boot
Mouse controller disabled
SCSI configuration incorrect standard SCSI controller
7.6 No mouse pointer displayed on the screen
7.10 Drives dead at system boot
7.12 Error messages on the screen
The Disk Array Controller configuration is incorrect
Disk Array Controller is not configured for this hard disk drive
8 System components and expansions
8.1 The SCSI hard disk subsystem
8.1.1 SCSI hard disk drives
System components and expansions
RAID level 0 and
RAID level 1 and 5 without standby hard disk
8.1.2 Replacement of SCSI hard disk drive during operation
Function of the indicators Green indicator
Orange indicator
The SCSI hard disk subsystem
8.1.3 Installing/removing a SCSI hard disk drive
System components and expansions
System components and expansions
8.1.4 SCSI platter for four 1-inch hard disk slide-in modules
The SCSI hard disk subsystem
8.2 Accessible drives
IDE drive
SCSI drive
System components and expansions
System components and expansions
8.2.1 Installing/Removing an accessible 5 ¼-inch drive
Accessible drives
8.2.2 Changing the floppy disk drive
System components and expansions
System components and expansions
8.3 Removing/installing boards
Removing/installing boards
System components and expansions
8.4.1 Installing/removing the chipDISK
8.4 chipDISK for RemoteView
8.4.2 Configuring the chipDISK
Diagnostic System
chipDISK for RemoteView
System components and expansions
8.5 Replacing the system fan
System components and expansions
8.6 Adapter module
8.7 System board
Adapter module
System components and expansions
Page
9 Index
Index
K Keyboard
Index
Index